Author Topic: update mcc 1435  (Read 613 times)

0 Members and 9 Guests are viewing this topic.

Offline jrdplowing

  • 4 cube
  • **
  • Posts: 26
  • Karma: 1

  • Total Badges: 8
    Badges: (View All)
    10 Posts Search Level 2 Karma Topic Starter Level 1
update mcc 1435
« on: September 17, 2015, 07:50:41 pm »
put new primer bulb on and was able to prime gas to carb properly,but the sticker on the machine says pump 10 times and i watched how much gas was going into the carb and it was like enough gas to start a 632 BB chevy,so after geting it unflooded it started and ran good again,now i go and start cutting logs and the chain got so tight it would not move,so  i removed the brake spring to see if that was the cause and it did the same thing after 2 logs,so readjusted again,2 times before it finnally continued to cut,any help would be appreciated on the problem of the chain tightening on its own,does this have an auto adjust,by looking at it i would think no,but thanks for any info,by the way when i got this saw from the garbage it had a broken front handle and the bar was bent to heck like you wouldnt believe,iam thinking the chain kept tightening on the previos owner and he wipped it at a tree because he was pissed,

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: update mcc 1435
« Reply #1 on: September 17, 2015, 07:54:33 pm »
I only push a purge or primer about 5 times.

Rest I am clueless on.

Offline Chris-PA

  • 6 cube
  • ****
  • Posts: 209
  • Karma: 32

  • Total Badges: 21
    Badges: (View All)
    Level 5 Third year Anniversary Second year Anniversary 100 Posts 50 Posts Level 4
Re: update mcc 1435
« Reply #2 on: September 17, 2015, 09:19:47 pm »
The purge bulb does not pump fuel into the carb. It pulls fuel through the carb and pumps it back into the tank to purge air from the lines.   If it's pumping fuel into the carb you have it connected backwards.

Offline pete

  • Gas Hotsaw
  • ******
  • Posts: 500
  • Karma: 37

  • Total Badges: 25
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Level 5 Sixth year Anniversary
Re: update mcc 1435
« Reply #3 on: September 18, 2015, 07:23:10 am »
The self tightening chain WAG is the oiler working dry chain will heat up quick and stop

Offline jrdplowing

  • 4 cube
  • **
  • Posts: 26
  • Karma: 1

  • Total Badges: 8
    Badges: (View All)
    10 Posts Search Level 2 Karma Topic Starter Level 1
Re: update mcc 1435
« Reply #4 on: September 18, 2015, 12:22:36 pm »
it says IN on the primer bulb and i have that hooked to the line comming from the tank, but i will check again,it has been getting good oil to the chain and when the saw sits it leaves an oil puddle,would also like to fix that,thanks for the help,and could use more info on the oil leak when sitting,thanks

Offline Chris-PA

  • 6 cube
  • ****
  • Posts: 209
  • Karma: 32

  • Total Badges: 21
    Badges: (View All)
    Level 5 Third year Anniversary Second year Anniversary 100 Posts 50 Posts Level 4
Re: update mcc 1435
« Reply #5 on: September 18, 2015, 10:38:19 pm »
it says IN on the primer bulb and i have that hooked to the line comming from the tank, but i will check again
In should go to the carb and out goes to the tank. 

Offline jrdplowing

  • 4 cube
  • **
  • Posts: 26
  • Karma: 1

  • Total Badges: 8
    Badges: (View All)
    10 Posts Search Level 2 Karma Topic Starter Level 1
Re: update mcc 1435
« Reply #6 on: September 18, 2015, 11:21:07 pm »
i would think it is just like all the fuel pumps i deal with, where IN is from the supply and OUT is to the demand,but it wouldnt suprise me,but when i pump the primer bulb why wouldnt it  take from the carb and pump into the tank,thanks

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

  • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: update mcc 1435
« Reply #7 on: September 18, 2015, 11:23:55 pm »
The idea is to pull fuel through the carb and get the air out.

With the carb full of fuel, the engine should run.
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline jrdplowing

  • 4 cube
  • **
  • Posts: 26
  • Karma: 1

  • Total Badges: 8
    Badges: (View All)
    10 Posts Search Level 2 Karma Topic Starter Level 1
Re: update mcc 1435
« Reply #8 on: September 19, 2015, 08:18:24 am »
thanks magnum,so should i reverse the lines on the bulb,where IN will be the carb line and OUT will be the tank line,thanks, any info on the puddle of oil when it sits not running

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
792 Views
Last post May 03, 2011, 09:38:41 pm
by Old Iron Logging
49 Replies
17104 Views
Last post February 13, 2016, 06:19:32 pm
by farmboy
2 Replies
530 Views
Last post August 27, 2014, 09:40:50 pm
by Red Elm
4 Replies
642 Views
Last post October 15, 2015, 10:43:07 pm
by ch74
2 Replies
496 Views
Last post September 12, 2015, 09:44:05 pm
by jrdplowing
8 Replies
592 Views
Last post September 13, 2015, 02:47:57 pm
by jrdplowing
4 Replies
468 Views
Last post October 19, 2015, 07:20:58 pm
by jrdplowing
3 Replies
727 Views
Last post December 08, 2017, 01:25:19 pm
by Tractorsaw1
2 Replies
581 Views
Last post November 13, 2020, 09:54:21 am
by Cut4fun
3 Replies
370 Views
Last post July 28, 2023, 11:13:04 am
by Cut4fun .