Author Topic: 44mm aftermarket 5000 plus and 490 pistons  (Read 1376 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21877
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
44mm aftermarket 5000 plus and 490 pistons
« on: January 08, 2014, 01:32:37 pm »
Finally someone is making them.  44mm aftermarket Partner 5000 plus and Jonsered 490 piston kit

http://store.chainsawr.com/products/jonsered-490-chainsaw-44mm-windowed-piston-kit-503-10-02-01-new
REDNECK Saw Repair Getter Done

Share on Facebook Share on Twitter


Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Yeah, but the dreaded two ear pin clips.
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21877
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Thats a easy fix.  I have many oem ones left over. If they fit.
 But I have sold out of all the 500 5000 490 stuff already anyways.  Still cool to see a aftermarket piston though.

NOS OEM kits was bringing 100-130.  I sold them for what I had in them to friends when I got out of the series.
REDNECK Saw Repair Getter Done

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #3 on: August 18, 2014, 11:16:14 pm »
Did husky use the closed port 44mm   jug on any saws? Have a couple clean 5000s with badly scored jugs I'd like to restore

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21877
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #4 on: August 21, 2014, 12:29:35 pm »
Did husky use the closed port 44mm   jug on any saws? Have a couple clean 5000s with badly scored jugs I'd like to restore

Only one I know of that fits in 44mm was the open port 50 in husky.  No closed port in 44mm I can think of, maybe I am forgetting one?
REDNECK Saw Repair Getter Done

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #5 on: August 21, 2014, 02:21:42 pm »
There's been mention of the closed port 44mm on other husky motors but I've never heard any definitive responses to that.

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 68
  • Information collector
  • Location: Troms, North Norway
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #6 on: September 03, 2014, 07:50:20 am »
Did husky use the closed port 44mm   jug on any saws? Have a couple clean 5000s with badly scored jugs I'd like to restore

Only one I know of that fits in 44mm was the open port 50 in husky.  No closed port in 44mm I can think of, maybe I am forgetting one?

I am not sure if the early 44mm 51 EPA saws used an open or a closed port one? It hardly is availiable anyway though, if it was a "special" for that version, as the concept of smaller bore EPA versions was short lived....

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #7 on: September 03, 2014, 12:21:09 pm »
Ordered the meteor piston/cylinder kit for the  partner,  I'll post a few pics when it arrives.  Just picked up a clean 51 with 45mm open port cyl.  Piston us lightly scored on exhaust side, cleaned up the cylinder and checked seals, all good.   Maybe overheated with dull chain?   Intake side was perfect, scored width of exhaust but ring wasn't stuck.  Kinda odd.   

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #8 on: September 03, 2014, 12:43:48 pm »
Found some "slab side" 45mm oem pistons that might work well with the open transfers. Anyone know the original application for p/n 502 128 002 was?
Adam

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21877
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #9 on: September 03, 2014, 01:25:24 pm »
Coming back to  Jonsered RS52  RS51 502128002 PISTON CPL 45 MM  oem $87  ( I havent a clue on what saw that is). I see that part number for husky too, but cant figure out in which saw.

Jred looks like a clearing saw?  http://www.jonsered.com/ddoc/JONI/JONI2002_AAaa/JONI2002_AAaa_106274262.pdf
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
24 Replies
1302 Views
Last post December 24, 2014, 04:26:20 pm
by 660magnum
7 Replies
522 Views
Last post December 24, 2012, 11:32:46 am
by 660magnum
2 Replies
463 Views
Last post February 13, 2013, 06:47:50 am
by Cut4fun .
3 Replies
391 Views
Last post October 21, 2013, 01:50:47 pm
by Spike60
2 Replies
363 Views
Last post September 26, 2013, 03:36:47 pm
by Cut4fun .
1 Replies
244 Views
Last post December 05, 2013, 03:41:38 am
by 660magnum
15 Replies
188 Views
Last post June 15, 2014, 11:07:55 am
by Cut4fun
2 Replies
108 Views
Last post November 12, 2014, 06:11:42 am
by jmester
10 Replies
413 Views
Last post September 25, 2014, 08:40:05 pm
by aclarke
15 Replies
1150 Views
Last post March 10, 2016, 02:51:43 pm
by Cut4fun .