« previous next »
Pages: 1 [2] 3 4 5 6   Go Down

Author Topic: 44mm aftermarket 5000 plus and 490 pistons  (Read 4583 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23935
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #10 on: September 03, 2014, 01:31:19 pm »
Logged

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #11 on: September 03, 2014, 02:28:14 pm »
Thanks Kevin. Dealer just ordered me one. I'll post measurements when I get it...
Logged

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #12 on: September 03, 2014, 02:32:53 pm »
Kev, may be a brush cutter based on the 50cc saw motors?  We have a 335 say based brush cutter, didn't know if that was a common practice with Husky/Jred prior to the 335xpt era?
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23935
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #13 on: September 03, 2014, 03:17:02 pm »
Yep looks like a little chainsaw motor PH.  Pin size the same? Noticed bolt on cylinder too.

I had a husky blower in that looked like a clamshell PH of small chainsaw.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23935
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #14 on: September 03, 2014, 03:22:23 pm »
Logged

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #15 on: September 03, 2014, 06:40:19 pm »
Thanks for thread links, good info! Net info I found says 10mm pin on the brush cutter. Will confirm in a few days. 
Logged

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4700
  • Karma: 216
  • OHIO REDNECK
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #16 on: September 04, 2014, 12:39:12 pm »
Adam I was thinking about this last night. Why not just use a 353 45mm piston?   

I am thinking why you choose the other one is due to way the slab side is made?

     
45mm Meteor Piston for Husqvarna Model 353
SKU: P714
Your Price:    $34.95

http://northwoodsaw.com/store/index.php?l=product_detail&p=1381


Logged

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #17 on: September 04, 2014, 03:21:18 pm »
Kev, I'll get one of those too. I'm curious how the full circle vs. Slab side will perform in the open port.   
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23935
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #18 on: September 07, 2014, 12:49:44 pm »
Quote from: SawTroll on September 03, 2014, 07:50:20 am
Quote from: Cut4fun_ on August 21, 2014, 12:29:35 pm
Quote from: aclarke on August 18, 2014, 11:16:14 pm
Did husky use the closed port 44mm   jug on any saws? Have a couple clean 5000s with badly scored jugs I'd like to restore

Only one I know of that fits in 44mm was the open port 50 in husky.  No closed port in 44mm I can think of, maybe I am forgetting one?

I am not sure if the early 44mm 51 EPA saws used an open or a closed port one? It hardly is availiable anyway though, if it was a "special" for that version, as the concept of smaller bore EPA versions was short lived....

Adam was helping a guy with a 44mm 350. I didnt see cylinder though.   Open or closed I dont know?

Jonsered 2149 had a closed port 44mm too. I remember one north of me that was woods ported now.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23935
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 44mm aftermarket 5000 plus and 490 pistons
« Reply #19 on: September 07, 2014, 12:53:12 pm »
Not windowed either 44mm 350

Logged
Pages: 1 [2] 3 4 5 6   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
0 Replies
193 Views 		Last post July 19, 2013, 10:02:28 am
by adam32
3 Replies
819 Views 		Last post October 21, 2013, 01:50:47 pm
by Spike60
9 Replies
479 Views 		Last post March 19, 2015, 10:41:01 am
by mowertech
1 Replies
707 Views 		Last post December 05, 2013, 03:41:38 am
by 660magnum
15 Replies
842 Views 		Last post June 15, 2014, 11:07:55 am
by Cut4fun
2 Replies
365 Views 		Last post November 12, 2014, 06:11:42 am
by jmester
10 Replies
1195 Views 		Last post September 25, 2014, 08:40:05 pm
by aclarke
15 Replies
2805 Views 		Last post March 10, 2016, 02:51:43 pm
by Cut4fun .
0 Replies
252 Views 		Last post June 13, 2023, 09:56:16 am
by Cut4fun .
2 Replies
142 Views 		Last post August 21, 2024, 07:24:28 am
by Cut4fun .