Author Topic: Partner 550 S55 P55 F55 65 650 P70 7000  (Read 10404 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21769
  • Karma: 519
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Partner 550 650 P70 7000
« Reply #30 on: November 20, 2011, 09:34:48 am »
This 550 has WJ with a governor built into carb. I bypassed it though with a bb.  ;)

My complete gasket kits came with seals in it.  I've bought several over the years and they all did too. I'm down to 1 or 2 and I have a 490 to split to put crank bearings in. But I may never with that saw.  Been stealing from it over time. There is no top end and other misc stuff missing now.

REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21769
  • Karma: 519
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Partner F55 Partner 1632
« Reply #31 on: November 29, 2011, 01:20:11 pm »
OK what is the difference in the F55 compared to my Partner 550?

 I see the Skil 1632 Partner 1632 all say they are a F55 farmer.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21769
  • Karma: 519
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Partner 550 650 P70 7000
« Reply #32 on: February 12, 2012, 04:24:28 pm »
First P70 I have seen woods ported. Looking good.

http://www.youtube.com/watch?v=XuE_XUoG1NM
REDNECK Saw Repair Getter Done

Offline chainsman1

  • 5 cube
  • ***
  • Posts: 105
  • Karma: 8
Re: Partner 550 650 P70 7000
« Reply #33 on: February 12, 2012, 10:59:41 pm »
Does anyone ever tried a k700 top end on one of those partner chainsaws?  Im curious if it would be as powerful as a p70 or so.

Offline timberdollars

  • 3 cube
  • *
  • Posts: 6
  • Karma: 0
Re: Partner 550 650 P70 7000
« Reply #34 on: February 21, 2012, 11:01:55 am »
I have both ported and non ported P70 and 7000+, P70 has the T-port the 7000/and plus do not. Plus is harder to start and I find No difference in power. My best one is a low hour P70 with T-port ported, it pulls with anything out there today!
K650/700 cylinder has larger ports and a wider intake track, is the best but NOT THE OPEN PORT Chinese, can't quite get a BOG outta the two I put together????? might be a timing issue but K series flywheels wont fit  chainsaw cases. lost interest in that combo decided to stick with P70's

Side note: my old small cooling fin 65cc Farmer ported (bridged intake/exguast) is just as fast if not faster than my ported P70's, I compared it many times!!!! has alot higher compression ratio and you feel it when you pull it over.

Duane

Offline Mastermind

  • 6 cube
  • ****
  • Posts: 224
  • Karma: 24
  • Location: Tennessee
Re: Partner 550 650 P70 7000
« Reply #35 on: April 20, 2012, 12:04:10 am »
First P70 I have seen woods ported. Looking good.

http://www.youtube.com/watch?v=XuE_XUoG1NM

Hey......I know that guy.

I have a pile of 55s and 65s that I'm building a 4 cube out of. I'll be posting here on those builds.
Mastermind Work Saws
931-863-5157

Offline rburg

  • 4 cube
  • **
  • Posts: 29
  • Karma: 5
Re: Partner 550 650 P70 7000
« Reply #36 on: April 20, 2012, 08:29:32 pm »
I believe I have run that partner.

Offline Mastermind

  • 6 cube
  • ****
  • Posts: 224
  • Karma: 24
  • Location: Tennessee
Re: Partner 550 650 P70 7000
« Reply #37 on: April 20, 2012, 09:09:57 pm »
Yes you did. That's one saw I should have hung onto. But......you can't keep them all.
Mastermind Work Saws
931-863-5157

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 68
  • Information collector
  • Location: Troms, North Norway
Re: Partner 550 650 P70 7000
« Reply #38 on: April 27, 2012, 10:30:03 am »
I have both ported and non ported P70 and 7000+, P70 has the T-port the 7000/and plus do not. Plus is harder to start and I find No difference in power. My best one is a low hour P70 with T-port ported, it pulls with anything out there today!
K650/700 cylinder has larger ports and a wider intake track, is the best but NOT THE OPEN PORT Chinese, can't quite get a BOG outta the two I put together????? might be a timing issue but K series flywheels wont fit  chainsaw cases. lost interest in that combo decided to stick with P70's

Side note: my old small cooling fin 65cc Farmer ported (bridged intake/exguast) is just as fast if not faster than my ported P70's, I compared it many times!!!! has alot higher compression ratio and you feel it when you pull it over.

Duane

Hmmmmm?? ???

When the P7000+ came out, they said there was a 15% power boost over the P7000, to 3.5 kW....

According to specs it wasn't 15%, but still over 10%, from 3.1 to 3.5 kW.

Offline pete

  • Piped Saw
  • *****
  • Posts: 491
  • Karma: 37
Re: Partner S65
« Reply #39 on: March 20, 2013, 06:43:26 am »
Hey cut  did you ever get an answer to this question  I have an s65 and a farmer 55 possible a bothe been on the shelf a long time now but time to bring them back into service, so seasls may be an issue cheers

 

Related Topics

  Subject / Started by Replies Last post
45 Replies
3662 Views
Last post September 22, 2015, 06:37:09 pm
by The Ripper
17 Replies
1343 Views
Last post February 16, 2020, 08:29:07 am
by Cut4fun .
partner 500

Started by man of stihl « 1 2 » Partner

18 Replies
1211 Views
Last post July 06, 2015, 05:35:27 pm
by aclarke
0 Replies
755 Views
Last post April 13, 2012, 01:45:51 pm
by man of stihl
5 Replies
582 Views
Last post February 15, 2013, 01:18:19 pm
by niel logman
7 Replies
632 Views
Last post June 09, 2013, 08:34:40 am
by HMLT360Pro
4 Replies
736 Views
Last post September 21, 2013, 05:54:01 pm
by Cut4fun
10 Replies
1842 Views
Last post February 11, 2014, 12:46:47 pm
by Cut4fun .
6 Replies
203 Views
Last post September 07, 2016, 05:26:30 pm
by Cut4fun .
2 Replies
141 Views
Last post December 19, 2017, 05:29:05 am
by Al Smith