Author Topic: partner 950  (Read 393 times)

0 Members and 0 Guests are viewing this topic.

Offline farmboy196

  • pruner
  • *
  • Posts: 2
  • Karma: 0
partner 950
« on: April 10, 2014, 12:31:09 am »
I got a partner 950 and cant get it to seal on the intake of the carb side i got new parts on the intake side  5062219-01    5036780-01    5061335-01  these are the only parts that would make it seal i have lost a top end and i believe that was from getting air at the intake is there something i should know on how to get this to seal thanks for your time Gerald

Social Buttons


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 17941
  • Karma: 338
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: partner 950
« Reply #1 on: April 10, 2014, 01:05:33 pm »
You talking about the K950?    Partner K950 IPL.  http://www.husqvarna.com/ddoc/PAII/PAII2002_AAaa/PAII2002_AAaa__106249364.pdf

Never had one come in to know anything sorry.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 17941
  • Karma: 338
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: partner 950
« Reply #2 on: April 10, 2014, 01:09:24 pm »
Found a workshop manual = service manual   partner k65 k700 k950  k1250 96pages

http://www.lacountyfirefighters.org/items/Partner_Workshop_manual.pdf
REDNECK Saw Repair Getter Done

Offline farmboy196

  • pruner
  • *
  • Posts: 2
  • Karma: 0
Re: partner 950
« Reply #3 on: April 14, 2014, 03:20:23 pm »
yes a k950 and that is the correct manual



sorry so long to get back had a death in the famliy

Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4001
  • Karma: 220
  • Location: Carpenter, Wyoming
Re: partner 950
« Reply #4 on: November 25, 2014, 12:17:42 am »
I just worked on a K 950 at work last week and noticed the same problem with it not sealing good between the intake and carb.   I used some Yamabond on the surface and that seemed to work.   I was told the intake was NLA.   This particular saw uses a special bar and chain for cutting concrete.  I have never seen another like it.  The saw also had all three clutch springs broken which I replaced.  The business I work for actually had those in stock.  When done the saw seemed to start, run, and idle ok.
PP 505, 475, 445.

 

Related Topics

  Subject / Started by Replies Last post
1 Replies
683 Views
Last post July 08, 2015, 02:43:49 pm
by Cut4fun .
10 Replies
1187 Views
Last post February 11, 2014, 12:46:47 pm
by Cut4fun .
Partner P85

Started by wkend lumberjak « 1 2 3 » Partner

22 Replies
691 Views
Last post December 12, 2014, 10:33:16 pm
by awol
0 Replies
260 Views
Last post December 27, 2014, 10:43:08 pm
by Cut4fun .
9 Replies
420 Views
Last post December 14, 2015, 07:23:53 pm
by Al Smith
12 Replies
546 Views
Last post May 06, 2016, 05:44:12 am
by chy_farm
4 Replies
169 Views
Last post May 14, 2016, 08:26:20 pm
by ffchewy17
8 Replies
320 Views
Last post February 08, 2017, 03:49:40 pm
by Cut4fun .
0 Replies
130 Views
Last post January 27, 2017, 11:33:16 am
by fisaw
Partner 510

Started by tyui Partner

1 Replies
85 Views
Last post March 14, 2017, 03:06:25 am
by nenicu