« previous next »
Pages: 1 [2]   Go Down

Author Topic: Which brands and Models have a clutch that will fit my 500 ?  (Read 1153 times)

0 Members and 0 Guests are viewing this topic.

Offline jeff.lary

  • 4 cube
  • **
  • Posts: 40
  • Karma: 8
Re: Which brands and Models have a clutch that will fit my 500 ?
« Reply #10 on: November 21, 2017, 08:22:41 am »
I don't come here very often but I wanted to say thank you to "Cut For Fun".
 I have a 5000 that is giving me fits lately and I think? it may be a seal. No matter how often I set the idle after a few minutes it is right back to a very high idle. The chain spinning very fast so it could be a clutch too. When I hold it upright( in the normal cutting position) it revs very high , but if I turn it on it's side ( PTO) down towards the ground the high rev goes away. In fact if I left it that way without blipping the throttle I think it would stall out.
  Well anyway I wanted to buy new seals and a new clutch but I could not find what I needed,.. then through googling ( clutches that will fit my 500 or 5000) I ended up finding this old thread.
  C.F.F had named several different part numbers that helped me find some parts I ordered 6 seals and one clutch last evening from HLSupplies . Thanks again you have always been a wealth of help to me and I am sure many others. Jeff
Logged
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23416
  • Karma: 661
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Which brands and Models have a clutch that will fit my 500 ?
« Reply #11 on: November 21, 2017, 08:27:47 am »
Quote from: jeff.lary on November 21, 2017, 08:22:41 am
I don't come here very often but I wanted to say thank you to "Cut For Fun".
 I have a 5000 that is giving me fits lately and I think? it may be a seal. No matter how often I set the idle after a few minutes it is right back to a very high idle. The chain spinning very fast so it could be a clutch too. When I hold it upright( in the normal cutting position) it revs very high , but if I turn it on it's side ( PTO) down towards the ground the high rev goes away. In fact if I left it that way without blipping the throttle I think it would stall out.
  Well anyway I wanted to buy new seals and a new clutch but I could not find what I needed,.. then through googling ( clutches that will fit my 500 or 5000) I ended up finding this old thread.
  C.F.F had named several different part numbers that helped me find some parts I ordered 6 seals and one clutch last evening from HLSupplies . Thanks again you have always been a wealth of help to me and I am sure many others. Jeff

 8) Thanks for feedback

Thats why I store the info broke down like I do here. Glad to here it helped even in a google search for you to find the info that could help you.

Logged

Offline jeff.lary

  • 4 cube
  • **
  • Posts: 40
  • Karma: 8
Re: Which brands and Models have a clutch that will fit my 500 ?
« Reply #12 on: November 25, 2017, 02:51:37 pm »
I just came out of the woods and checked the mail. I now have 6 count em 6 new crank seals and a new clutch. They are Hyway brand from hlsupply. Now I need a new bar,.. today I was finishing up my thinning for this year in my rock maple grove and had to drop a poplar. It / I managed to get my bar pinched then before I could do anything about it the tree slid off the stump and bent/ twisted the bar right at the replaceable tip so it screwed them both I think. I will have you a shop day tomorrow and look at it. I swear you cannot have enough replacement parts around. I have been very lucky though I have never ruined a bar in all my years and this one was a Forrester so it was not too expensive anyway. I have heard nothing good about Forrester bars but for the money they have been ok to me.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23416
  • Karma: 661
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Which brands and Models have a clutch that will fit my 500 ?
« Reply #13 on: November 25, 2017, 03:53:46 pm »
Let us know how those aftermarket seals hold up.  Never ordered seals from HL. Only used oem in partner saws.
Logged

Offline jeff.lary

  • 4 cube
  • **
  • Posts: 40
  • Karma: 8
Re: Which brands and Models have a clutch that will fit my 500 ?
« Reply #14 on: November 26, 2017, 12:38:44 pm »
I got them put in and the new clutch put on now I just need to have time to run it some. When removing the seals I noticed that the Flywheel side seal was not in straight. One side was higher than the other by about 1/16 to an 1/8", don't know if that may have caused the fast idle issue or not.
Logged
Like Like x 1 View List
Pages: 1 [2]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
3 Replies
494 Views 		Last post October 29, 2011, 04:08:19 pm
by SOLOmann
1 Replies
401 Views 		Last post September 13, 2012, 10:18:38 am
by Cut4fun
1 Replies
314 Views 		Last post October 19, 2013, 11:59:12 pm
by stihls066
3 Replies
203 Views 		Last post May 20, 2014, 01:45:58 pm
by jcsmith
1 Replies
387 Views 		Last post September 06, 2014, 01:08:50 pm
by aclarke
48 Replies
1770 Views 		Last post March 17, 2015, 01:15:05 pm
by SawTroll
0 Replies
485 Views 		Last post February 04, 2017, 10:46:00 am
by mowertech
1 Replies
163 Views 		Last post November 05, 2017, 08:31:15 am
by ray benson
2 Replies
1468 Views 		Last post April 06, 2017, 01:38:08 pm
by Cut4fun .
0 Replies
357 Views 		Last post August 20, 2019, 08:45:37 am
by Cut4fun .