Author Topic: Performance Outdoor Equipment....Dolmar parts  (Read 1791 times)

0 Members and 0 Guests are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2037
  • Karma: 199
  • Magnesium and Iron.
  • Location: Northern California.
Re: Performance Outdoor Equipment....Dolmar parts
« Reply #50 on: July 17, 2015, 03:21:08 pm »
that depends on how it is made and the stud spacing of those poulans compared to the echo saws. unfortunately i wont have one in my hand to check out till this order is delivered.

You could send one of those P4 adapters to me to try on those Poulans. 8)

Those P4 adapters is the main reason i am doing this. Mentioned they were coming out with them over on AS and got swamped with "I want one" I'll take 2" so decided to get a handle on just how many i need to order. I didnt want to order 20 and sell 40 or order 100 and only sell 10. I am ordering extra so i will have one to to take some measurements from. If they will work on the poulans i can send a couple your way after i get the order.

Sounds good Nathan.  I only have one D176 mount Echo right now (CS500VL that I don't really need to run S1 bars on), but have several 61-85cc Poulans and other A176/D176 mount saws to try that adapter on.  If that adapter works on those saws (and I'm thinking it will) then that'll broaden your market.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 425
  • Karma: 80
  • Location: Newcomerstown ,Ohio
Re: Performance Outdoor Equipment....Dolmar parts
« Reply #51 on: July 17, 2015, 06:46:44 pm »
As of right now i am planning on 30 extra adapters over what gets spoken for and hoping that will cover me till my next order.

On the bar front we are halfway to the 20 bar goal so hopefully some other guys decide they want a cannon bar.
5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered


Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1832
  • Karma: 162
Re: Performance Outdoor Equipment....Dolmar parts
« Reply #52 on: July 17, 2015, 08:10:19 pm »
How soon you going to order? I need to get some stuff built and sold before I buy more bars.

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 425
  • Karma: 80
  • Location: Newcomerstown ,Ohio
Re: Performance Outdoor Equipment....Dolmar parts
« Reply #53 on: July 18, 2015, 08:35:45 am »
planning on ordering early next week but that can be put off till end of the week(july 24) because those echo bar adapters wont be ready for shipment till 2nd week of august if what they told me actaully holds true.
5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered


Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1832
  • Karma: 162
Re: Performance Outdoor Equipment....Dolmar parts
« Reply #54 on: July 18, 2015, 09:22:57 am »
Ok. I was wondering. Trying to think if I need any more bars in small mount.

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 327
  • Karma: 28
Re: Performance Outdoor Equipment....Dolmar parts
« Reply #55 on: July 20, 2015, 03:30:01 pm »
need a bar and chain for ms250 new or used ok if plenty life in it. had to tell customer his was unsafe refuse to mount it. had ran 3/8 chain on it. shipping to 35674

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 17949
  • Karma: 338
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Performance Outdoor Equipment....Dolmar parts
« Reply #56 on: July 20, 2015, 04:37:47 pm »
need a bar and chain for ms250 new or used ok if plenty life in it. had to tell customer his was unsafe refuse to mount it. had ran 3/8 chain on it. shipping to 35674

Full size 3/8 on a 250?  :o
REDNECK Saw Repair Getter Done

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 327
  • Karma: 28
Re: Performance Outdoor Equipment....Dolmar parts
« Reply #57 on: July 20, 2015, 07:02:21 pm »
i think  he likes a little moonshine. rim was toast roller teeth sharp as knife rails ugly  looked like .050 was run on .063 rails dont know if it was lo pro or regular 3/8 but did nasty job on .325 bar.

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 425
  • Karma: 80
  • Location: Newcomerstown ,Ohio
Re: Performance Outdoor Equipment....Dolmar parts
« Reply #58 on: July 21, 2015, 09:51:23 am »
need a bar and chain for ms250 new or used ok if plenty life in it. had to tell customer his was unsafe refuse to mount it. had ran 3/8 chain on it. shipping to 35674

i have nothing used that is worth shipping. Total 2 bars are cheap and decent bars if you want to go new. 16" 3/8lp is $16.95 plus $12 for a chain. and 16" .325 is $20.95  plus $14 for a chain. shipping would be about $8.
5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered


Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 327
  • Karma: 28
Re: Performance Outdoor Equipment....Dolmar parts
« Reply #59 on: July 21, 2015, 01:18:48 pm »
I will run that by customer the guys here had good words about your bars.

 

Related Topics

  Subject / Started by Replies Last post
12 Replies
588 Views
Last post January 11, 2012, 01:49:08 pm
by jmester
4 Replies
1008 Views
Last post January 10, 2012, 01:40:57 pm
by Cut4fun
12 Replies
524 Views
Last post September 27, 2013, 12:32:35 pm
by Playinwood
5 Replies
1551 Views
Last post July 28, 2012, 01:14:15 pm
by Al Smith
8 Replies
114 Views
Last post October 14, 2014, 09:54:07 pm
by farmboy
Dolmar parts

Started by aclarke « 1 2 » Dolmar Makita

11 Replies
594 Views
Last post April 23, 2014, 11:50:04 am
by KilliansRedLeo
5 Replies
388 Views
Last post June 10, 2014, 04:01:41 pm
by Nathaniel Vansickle
41 Replies
657 Views
Last post May 08, 2015, 12:14:40 pm
by aclarke
8 Replies
462 Views
Last post August 08, 2015, 12:07:52 pm
by SawTroll
9 Replies
236 Views
Last post December 08, 2015, 06:28:00 am
by Fish