Author Topic: Pioneer p41 chain saw parts  (Read 1871 times)

0 Members and 0 Guests are viewing this topic.

Offline Bob

  • 3 cube
  • *
  • Posts: 16
  • Karma: 0
Pioneer p41 chain saw parts
« on: April 01, 2014, 01:57:41 pm »
Hi,
Does anyone know where I can find new or good used parts for a Pioneer p41?  Thought I found parts on ebay but they had already sold.
Looking for the following:
47355 piston
430410 rings   
430924 cylinder head or cylinder head kit
Thank you,
Bob

Social Buttons


Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Pioneer p41 chain saw parts
« Reply #1 on: April 01, 2014, 03:03:35 pm »
I rebuilt a P-41 a year or so ago, these guys had all the parts I needed in stock.

http://rottmansales.com/
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline Bob

  • 3 cube
  • *
  • Posts: 16
  • Karma: 0
Re: Pioneer p41 chain saw parts
« Reply #2 on: April 01, 2014, 03:51:26 pm »
Thanks Killian,
 Rottman's said it comes as a kit, the kit contains a flywheel, cylinder and coil, piston and rings are additional and you have to change the flywheel &coil for the new cylinder.
Do you have to replace your cylinder & piston?
Thank you,
Bob

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Pioneer p41 chain saw parts
« Reply #3 on: April 01, 2014, 03:56:04 pm »
The need to replace the C/P depends on if your is messed up. I did the whole thing because that is what the customer wanted. Some of the very early ones used points ignition. My recommendation would be to go to electronic ignition which requires a different cylinder that is why it is in the kit. Also make sure you replace the reeds and reed box gasket.

If you have never run a P-41, you will like it, very nice powerful saws!
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline Bob

  • 3 cube
  • *
  • Posts: 16
  • Karma: 0
Re: Pioneer p41 chain saw parts
« Reply #4 on: April 01, 2014, 04:17:35 pm »
Thanks Killians,
Yes piston & cylinder are trashed, flywheel and coil are ok, was just wondering why they to be replaced because of the new cylinder? Does the new piston have to go in a certain way, in other words does it matter which side of the piston faces the exhaust port?
Was a favorite saw of mine, took good care of it till I loaned it to my father pretty sure he put regular gas in it when he gave it back had no compression.
This is becoming a costly restore.
Thank you for all your help I really appreciate it.
Bob

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Pioneer p41 chain saw parts
« Reply #5 on: April 01, 2014, 08:07:18 pm »
Bob, too bad about the raw gas situation. Yes the piston only goes in one way, there is usually an arrow on the top of the piston that is supposed to point to the exhaust port.
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6366
  • Karma: 227
  • For The Love Of Chainsaws
  • Location: NCO
Re: Pioneer p41 chain saw parts
« Reply #6 on: April 01, 2014, 09:07:32 pm »
I don't know about the P-41 but some western European chainsaw pistons have the arrow pointing towards the intake side with a big capital "E" imprinted at the arrow. The "E" is for Enlass or "Intake" in English.

The bottom line is to look for the ring pins. The ring pins must be where they do not come across a port!
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Pioneer p41 chain saw parts
« Reply #7 on: April 01, 2014, 09:50:02 pm »
Good post Jim, +1!
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline fordfairlane78

  • 6 cube
  • ****
  • Posts: 160
  • Karma: 16
  • Location: Valley Center,KS
Re: Pioneer p41 chain saw parts
« Reply #8 on: April 02, 2014, 03:38:38 am »
Tommysp1 has pioneer parts as well. This is a member on this site. Have you already torn down the saw and confirmed that the p/c are toast? I don't remember if the p 41 had a compression release or if it had the automatic release engaged by the rope pulley but these could be problems if you don't already know if the p/c are bad....
Trapped in time, surrounded by evil, low on gas

 

Related Topics

  Subject / Started by Replies Last post
7 Replies
1553 Views
Last post October 21, 2011, 07:55:21 pm
by Spike60
5 Replies
741 Views
Last post October 28, 2013, 12:29:05 pm
by leec
3 Replies
575 Views
Last post June 07, 2012, 02:47:11 pm
by Dh1984
7 Replies
1144 Views
Last post December 22, 2013, 01:31:52 pm
by dutchsawdoctor
1 Replies
411 Views
Last post May 23, 2013, 12:55:10 am
by fordfairlane78
9 Replies
892 Views
Last post November 05, 2014, 10:35:55 pm
by 67L36Driver
Pioneer Pics

Started by fossil « 1 2 » Pioneer

12 Replies
1159 Views
Last post November 19, 2014, 10:12:34 am
by KilliansRedLeo
9 Replies
790 Views
Last post April 06, 2014, 12:33:25 pm
by Tractorsaw1
2 Replies
333 Views
Last post October 03, 2014, 11:32:49 am
by fossil
4 Replies
243 Views
Last post August 16, 2015, 09:26:02 pm
by kb85