Author Topic: ebay and epa say bye bye to carb tools  (Read 421 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21878
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: ebay and epa say bye bye to carb tools
« Reply #10 on: September 19, 2015, 01:00:31 pm »
Stop adjusting carbs?  That dont make any sense IMO.

Bad aka poor running saw would put off more crap IMO.  WTHeck are they thinking.



I blocked this board for time being from guest. That way you need to be signed in to see this. Just in case.  :P
REDNECK Saw Repair Getter Done

Offline fisaw

  • 5 cube
  • ***
  • Posts: 84
  • Karma: 25
Re: ebay and epa say bye bye to carb tools
« Reply #11 on: September 20, 2015, 04:50:05 am »
Stop adjusting carbs?  That dont make any sense IMO.

Bad aka poor running saw would put off more crap IMO.  WTHeck are they thinking.
        I agree  , that's not good for the environment.

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: ebay and epa say bye bye to carb tools
« Reply #12 on: September 20, 2015, 11:00:12 am »
Racing vehicles (karts, bikes,sleds,saws) don't fall under EPA regs.

rewording the add on Ebay may get them off your back.  The guys who modify mufflers did the same on ebay years back

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21878
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: ebay and epa say bye bye to carb tools
« Reply #13 on: September 20, 2015, 11:17:18 am »
Good idea Adam.

Not for your stock saws use for you racesaws only. ;)   
REDNECK Saw Repair Getter Done

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: ebay and epa say bye bye to carb tools
« Reply #14 on: September 20, 2015, 06:44:19 pm »
I think Wojo got some nasty grams from Ebay about the non epa mufflers he sold.  Changed the description to read competition use only and he's been good since...

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21878
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: ebay and epa say bye bye to carb tools
« Reply #15 on: September 20, 2015, 07:08:42 pm »
Heck ya right on,  I would try that if I was him on the carb adjusting tools.   @DefinitiveDave
REDNECK Saw Repair Getter Done

Offline jr27236

  • 3 cube
  • *
  • Posts: 19
  • Karma: 5
Re: ebay and epa say bye bye to carb tools
« Reply #16 on: September 20, 2015, 07:28:18 pm »
Mine would read  carb repair tools, to keep your machine in EPA compliance after it breaks in and falls out of adjustment"

Sent from my SM-G920V using Tapatalk


Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2746
  • Karma: 164
Re: ebay and epa say bye bye to carb tools
« Reply #17 on: October 13, 2015, 05:23:10 am »
The EPA is helping themselves to get a feather in their hat?
Perhaps that feather needs installed in another part of the anatomy.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: ebay and epa say bye bye to carb tools
« Reply #18 on: October 14, 2015, 02:38:04 pm »
The EPA is helping themselves to get a feather in their hat?
Perhaps that feather needs installed in another part of the anatomy.

Yessir.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline pigpen60

  • 5 cube
  • ***
  • Posts: 143
  • Karma: 10
Re: ebay and epa say bye bye to carb tools
« Reply #19 on: November 20, 2015, 05:23:57 pm »
ok where do we find these evil tools?

 

Related Topics

  Subject / Started by Replies Last post
37 Replies
4702 Views
Last post February 21, 2014, 03:18:14 am
by fordfairlane78
11 Replies
537 Views
Last post November 01, 2013, 09:19:50 pm
by 660magnum
55 Jug on Ebay?

Started by alsled « 1 2 » Husqvarna

14 Replies
263 Views
Last post December 15, 2013, 01:07:15 pm
by farmboy
40 Replies
610 Views
Last post December 23, 2013, 04:24:37 pm
by Cut4fun
35 Replies
1067 Views
Last post November 11, 2016, 11:28:35 pm
by pete
25 Replies
730 Views
Last post June 25, 2014, 04:48:31 pm
by KilliansRedLeo
8 Replies
467 Views
Last post November 18, 2014, 09:08:42 pm
by Cut4fun .
0 Replies
82 Views
Last post November 18, 2014, 08:09:58 pm
by Cut4fun .
5 Replies
502 Views
Last post January 20, 2015, 05:24:39 pm
by 660magnum
0 Replies
233 Views
Last post November 25, 2015, 10:04:52 am
by Cut4fun .