Author Topic: how to: connecting rod length  (Read 120 times)

0 Members and 0 Guests are viewing this topic.

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52
how to: connecting rod length
« on: April 09, 2015, 10:04:02 pm »
.
hiatus

Share on Facebook Share on Twitter


Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4460
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: how to: connecting rod length
« Reply #1 on: April 11, 2015, 12:24:41 am »
So let me get this straight.   You put a drill bit into the piston where the wrist pin goes and then measured from the bottom of the drill bit to the top of the nut holding on the flywheel.   

Ok I magnified the last picture that has the instructions.   Got it, thanks for the info.
PP 505, 475, 445.

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52
Re: how to: connecting rod length
« Reply #2 on: April 11, 2015, 07:24:37 am »
sorry, was having a difficult time sizing the photos to be able to post them.

will try again.

have an idea to making a jig to hopefully make this process more accurate.

 larger photo:
hiatus

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4045
  • Karma: 159
  • OHIO REDNECK
Re: how to: connecting rod length
« Reply #3 on: April 11, 2015, 09:19:22 am »
You can post larger sized pics if you resize them using 72 instead of 300 that they are taken in. I know my small camera pics are over 1mb per pic in 300. I resize then to 200kb give or take in 72. 
REDNECK Saw Repair

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4045
  • Karma: 159
  • OHIO REDNECK
Re: how to: connecting rod length
« Reply #4 on: April 11, 2015, 09:24:56 am »
Testing to see what your 1st pic was in.  Yours is 96 pixels per square inch. Resize at 72 pixels and you will have bigger pics shown.  With the same amount of KB space used.

I went to 72 and resized bigger for test.  Man dropped it to 19KB too.

If you are using one of these smart phone thingymbobs. Get the Tapatalk app and it will post pics straight to here and resize them too.



REDNECK Saw Repair

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: how to: connecting rod length
« Reply #5 on: April 11, 2015, 10:53:33 am »
Cool!

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52
Re: how to: connecting rod length
« Reply #6 on: April 11, 2015, 02:11:57 pm »
scrap tool idea and use.

lots of room for improvement.


hiatus

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52
Re: how to: connecting rod length
« Reply #7 on: April 19, 2015, 10:07:34 am »
please note....below is a photo of the correct method of math.  stroke needs to be divided by two.

as i was putting the numbers into my lottery ping pong ball shaker.....noticed that some strange numbers were being chosen.

anyhow....sorry for posting the error in the first place.

-joe
hiatus

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
304 Views
Last post April 07, 2011, 08:43:57 pm
by Old Iron Logging
3 Replies
693 Views
Last post December 11, 2012, 08:28:41 am
by davbell22602
2 Replies
164 Views
Last post March 19, 2013, 04:14:39 am
by Al Smith
Bar Length

Started by maxmag « 1 2 3 » Husqvarna

29 Replies
530 Views
Last post February 22, 2014, 07:50:14 pm
by gunrac
45 Replies
1685 Views
Last post January 05, 2015, 10:02:36 pm
by super44
5 Replies
194 Views
Last post September 17, 2015, 06:46:44 pm
by Cut4fun .
0 Replies
112 Views
Last post November 29, 2015, 11:01:10 am
by DaveJ
0 Replies
161 Views
Last post November 29, 2015, 11:55:23 am
by Cut4fun .
3 Replies
301 Views
Last post November 07, 2016, 05:25:48 pm
by oldpro
23 Replies
878 Views
Last post September 15, 2019, 02:50:06 pm
by Cut4fun .