Author Topic: how to: connecting rod length  (Read 401 times)

0 Members and 46 Guests are viewing this topic.

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52

  • Total Badges: 22
    Badges: (View All)
    Third year Anniversary Level 5 500 Posts Apple User Second year Anniversary One year Anniversary
how to: connecting rod length
« on: April 09, 2015, 10:04:02 pm »
.
hiatus

Share on Facebook Share on Twitter


Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

  • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: how to: connecting rod length
« Reply #1 on: April 11, 2015, 12:24:41 am »
So let me get this straight.   You put a drill bit into the piston where the wrist pin goes and then measured from the bottom of the drill bit to the top of the nut holding on the flywheel.   

Ok I magnified the last picture that has the instructions.   Got it, thanks for the info.
PP 505, 475, 445.

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52

  • Total Badges: 22
    Badges: (View All)
    Third year Anniversary Level 5 500 Posts Apple User Second year Anniversary One year Anniversary
Re: how to: connecting rod length
« Reply #2 on: April 11, 2015, 07:24:37 am »
sorry, was having a difficult time sizing the photos to be able to post them.

will try again.

have an idea to making a jig to hopefully make this process more accurate.

 larger photo:
hiatus

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4666
  • Karma: 216
  • OHIO REDNECK

  • Total Badges: 44
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 7 Seventh year Anniversary Apple User
Re: how to: connecting rod length
« Reply #3 on: April 11, 2015, 09:19:22 am »
You can post larger sized pics if you resize them using 72 instead of 300 that they are taken in. I know my small camera pics are over 1mb per pic in 300. I resize then to 200kb give or take in 72. 

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4666
  • Karma: 216
  • OHIO REDNECK

  • Total Badges: 44
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 7 Seventh year Anniversary Apple User
Re: how to: connecting rod length
« Reply #4 on: April 11, 2015, 09:24:56 am »
Testing to see what your 1st pic was in.  Yours is 96 pixels per square inch. Resize at 72 pixels and you will have bigger pics shown.  With the same amount of KB space used.

I went to 72 and resized bigger for test.  Man dropped it to 19KB too.

If you are using one of these smart phone thingymbobs. Get the Tapatalk app and it will post pics straight to here and resize them too.




Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172

  • Total Badges: 25
    Badges: (View All)
    Fourth year Anniversary Third year Anniversary 1000 Posts Second year Anniversary Level 5 500 Posts
Re: how to: connecting rod length
« Reply #5 on: April 11, 2015, 10:53:33 am »
Cool!

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52

  • Total Badges: 22
    Badges: (View All)
    Third year Anniversary Level 5 500 Posts Apple User Second year Anniversary One year Anniversary
Re: how to: connecting rod length
« Reply #6 on: April 11, 2015, 02:11:57 pm »
scrap tool idea and use.

lots of room for improvement.


hiatus

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52

  • Total Badges: 22
    Badges: (View All)
    Third year Anniversary Level 5 500 Posts Apple User Second year Anniversary One year Anniversary
Re: how to: connecting rod length
« Reply #7 on: April 19, 2015, 10:07:34 am »
please note....below is a photo of the correct method of math.  stroke needs to be divided by two.

as i was putting the numbers into my lottery ping pong ball shaker.....noticed that some strange numbers were being chosen.

anyhow....sorry for posting the error in the first place.

-joe
hiatus

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
593 Views
Last post April 07, 2011, 08:43:57 pm
by Old Iron Logging
3 Replies
1005 Views
Last post December 11, 2012, 08:28:41 am
by davbell22602
2 Replies
429 Views
Last post March 19, 2013, 04:14:39 am
by Al Smith
Bar Length

Started by maxmag « 1 2 3 » Husqvarna

29 Replies
1408 Views
Last post February 22, 2014, 07:50:14 pm
by gunrac
45 Replies
2790 Views
Last post January 05, 2015, 10:02:36 pm
by super44
5 Replies
490 Views
Last post September 17, 2015, 06:46:44 pm
by Cut4fun .
0 Replies
240 Views
Last post November 29, 2015, 11:01:10 am
by DaveJ
0 Replies
293 Views
Last post November 29, 2015, 11:55:23 am
by Cut4fun .
3 Replies
575 Views
Last post November 07, 2016, 05:25:48 pm
by oldpro
1 Replies
301 Views
Last post November 10, 2022, 07:11:57 pm
by Elden