« previous next »
Pages: [1]   Go Down

Author Topic: muffler installation made easy  (Read 156 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22183
  • Karma: 560
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
muffler installation made easy
« on: February 04, 2015, 02:17:58 pm »
Guy on my FB CSR site just posted this trick he uses at his stihl dealership.

(((((((Here's a trick to make muffler installation easy. Strips made out of plastic hold screws and gasket until screws started , then just pull them off and tighten screws.))))))


Logged
REDNECK Saw Repair Getter Done

Share on Facebook Share on Twitter

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22183
  • Karma: 560
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: muffler installation made easy
« Reply #1 on: February 04, 2015, 02:18:50 pm »
I am going to try this on those huskys with all the shields etc.
Logged
REDNECK Saw Repair Getter Done

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: muffler installation made easy
« Reply #2 on: February 04, 2015, 03:35:21 pm »
That's cool...
Logged

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171
Re: muffler installation made easy
« Reply #3 on: February 04, 2015, 03:38:02 pm »
I'll have to use that myself.
Logged

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 149
  • Location: Hayesville, NC
Re: muffler installation made easy
« Reply #4 on: February 04, 2015, 10:48:06 pm »
I LIKE!!!!!!!!
Shep
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22183
  • Karma: 560
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: muffler installation made easy
« Reply #5 on: March 26, 2015, 03:29:09 pm »
 Ended up using that muffler trick shown. shield, tank guard, gasket, muffler all held together as one piece.  Being I used a index card and just pushed holes through, I did rip that into and had to dig the one side out. Plastic like shown in that thread would be the cats meow. 
Logged
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: muffler installation made easy
« Reply #6 on: March 27, 2015, 02:31:56 pm »
Pretty slick.
Logged
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline JohnG28

  • Piped Saw
  • *****
  • Posts: 315
  • Karma: 27
Re: muffler installation made easy
« Reply #7 on: March 27, 2015, 10:35:40 pm »
Now that's a nice trick, I like it.  8)
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
0 Replies
275 Views 		Last post December 31, 2012, 02:18:19 pm
by Cut4fun .
24 Replies
913 Views 		Last post October 23, 2014, 12:22:01 pm
by Cut4fun .
0 Replies
70 Views 		Last post January 11, 2014, 01:51:50 pm
by KilliansRedLeo
10 Replies
379 Views 		Last post September 06, 2014, 07:00:15 pm
by Fish
39 Replies
324 Views 		Last post February 01, 2016, 05:28:44 pm
by countryhog
7 Replies
251 Views 		Last post June 27, 2016, 09:34:26 pm
by mrbb
7 Replies
865 Views 		Last post April 08, 2016, 01:16:15 pm
by Cut4fun .
6 Replies
163 Views 		Last post June 22, 2017, 09:43:36 am
by 660magnum
1 Replies
91 Views 		Last post September 28, 2018, 07:29:55 am
by rayvil01
1 Replies
54 Views 		Last post November 02, 2020, 08:49:39 pm
by fossil