« previous next »
Pages: [1]   Go Down

Author Topic: how to: connecting rod length  (Read 291 times)

0 Members and 0 Guests are viewing this topic.

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52
how to: connecting rod length
« on: April 09, 2015, 10:04:02 pm »
.
Logged
hiatus

Share on Facebook Share on Twitter

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4688
  • Karma: 319
  • Location: Carpenter, Wyoming
Re: how to: connecting rod length
« Reply #1 on: April 11, 2015, 12:24:41 am »
So let me get this straight.   You put a drill bit into the piston where the wrist pin goes and then measured from the bottom of the drill bit to the top of the nut holding on the flywheel.   

Ok I magnified the last picture that has the instructions.   Got it, thanks for the info.
Logged
PP 505, 475, 445.

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52
Re: how to: connecting rod length
« Reply #2 on: April 11, 2015, 07:24:37 am »
sorry, was having a difficult time sizing the photos to be able to post them.

will try again.

have an idea to making a jig to hopefully make this process more accurate.

 larger photo:
Logged
hiatus

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4574
  • Karma: 215
  • OHIO REDNECK
Re: how to: connecting rod length
« Reply #3 on: April 11, 2015, 09:19:22 am »
You can post larger sized pics if you resize them using 72 instead of 300 that they are taken in. I know my small camera pics are over 1mb per pic in 300. I resize then to 200kb give or take in 72. 
Logged

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4574
  • Karma: 215
  • OHIO REDNECK
Re: how to: connecting rod length
« Reply #4 on: April 11, 2015, 09:24:56 am »
Testing to see what your 1st pic was in.  Yours is 96 pixels per square inch. Resize at 72 pixels and you will have bigger pics shown.  With the same amount of KB space used.

I went to 72 and resized bigger for test.  Man dropped it to 19KB too.

If you are using one of these smart phone thingymbobs. Get the Tapatalk app and it will post pics straight to here and resize them too.



Logged

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: how to: connecting rod length
« Reply #5 on: April 11, 2015, 10:53:33 am »
Cool!
Logged

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52
Re: how to: connecting rod length
« Reply #6 on: April 11, 2015, 02:11:57 pm »
scrap tool idea and use.

lots of room for improvement.


Logged
hiatus

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52
Re: how to: connecting rod length
« Reply #7 on: April 19, 2015, 10:07:34 am »
please note....below is a photo of the correct method of math.  stroke needs to be divided by two.

as i was putting the numbers into my lottery ping pong ball shaker.....noticed that some strange numbers were being chosen.

anyhow....sorry for posting the error in the first place.

-joe
Logged
hiatus
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
3 Replies
491 Views 		Last post April 07, 2011, 08:43:57 pm
by Old Iron Logging
3 Replies
858 Views 		Last post December 11, 2012, 08:28:41 am
by davbell22602
2 Replies
318 Views 		Last post March 19, 2013, 04:14:39 am
by Al Smith
Bar Length

Started by maxmag « 1 2 3 » Husqvarna

29 Replies
1139 Views 		Last post February 22, 2014, 07:50:14 pm
by gunrac
45 Replies
2494 Views 		Last post January 05, 2015, 10:02:36 pm
by super44
5 Replies
335 Views 		Last post September 17, 2015, 06:46:44 pm
by Cut4fun .
0 Replies
182 Views 		Last post November 29, 2015, 11:01:10 am
by DaveJ
0 Replies
235 Views 		Last post November 29, 2015, 11:55:23 am
by Cut4fun .
3 Replies
456 Views 		Last post November 07, 2016, 05:25:48 pm
by oldpro
1 Replies
205 Views 		Last post November 10, 2022, 07:11:57 pm
by Elden