Author Topic: 3450 tank/handle replacement  (Read 368 times)

0 Members and 0 Guests are viewing this topic.

Offline rockfishon

  • 4 cube
  • **
  • Posts: 59
  • Karma: 8
Re: 3450 tank/handle replacement
« Reply #10 on: October 05, 2014, 11:17:58 am »
OK, sorry for the long delay.  I finally replaced the handle assembly.  The steps were exactly as posted.  If I were to do it again:
  • Don't misplace the replacement tank assembly - it will take a long time to find
  • The black expansion covers are hard to remove.  It is only the very top part that pops out.
  • The saw will not run without the choke if you don't attach the pulse line
  • The hose clamp on the pulse line will not be there if you forget to connect it

Thanks again everyone for the great help!  Now I have to figure out the carb, which will be another post.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22584
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 3450 tank/handle replacement
« Reply #11 on: October 05, 2014, 11:26:27 am »
OK, sorry for the long delay.  I finally replaced the handle assembly.  The steps were exactly as posted.  If I were to do it again:
  • Don't misplace the replacement tank assembly - it will take a long time to find
  • The black expansion covers are hard to remove.  It is only the very top part that pops out.
  • The saw will not run without the choke if you don't attach the pulse line
  • The hose clamp on the pulse line will not be there if you forget to connect it

Thanks again everyone for the great help!  Now I have to figure out the carb, which will be another post.

Good deal. Nice to read about closure.  Folks helping each other out to learn to do it themselves too.


What is this? = The black expansion covers are hard to remove.  It is only the very top part that pops out.
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2112
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northwestern Wyoming
Re: 3450 tank/handle replacement
« Reply #12 on: October 05, 2014, 07:37:46 pm »
Kevin I believe he's referring to the plastic plugs that pop inside of the conical rubber AV buffers at the bottom of the saw.  They're locked in place with the screws that thread into them.  They can be a bit reluctant to pop out.  I found persuading new conical rubber AV mounts to snap into the crankcase holes to be a far more challenging task than getting the plastic plugs out....

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4548
  • Karma: 292
  • Location: Carpenter, Wyoming
Re: 3450 tank/handle replacement
« Reply #13 on: October 05, 2014, 11:23:57 pm »
Good to hear you are making progress.
PP 505, 475, 445.

 

Related Topics

  Subject / Started by Replies Last post
0 Replies
65 Views
Last post March 05, 2013, 08:29:00 pm
by CG Racing
0 Replies
139 Views
Last post September 26, 2013, 10:14:34 am
by KilliansRedLeo
40 Replies
725 Views
Last post January 30, 2014, 10:44:24 am
by 660magnum
16 Replies
1246 Views
Last post April 11, 2014, 07:03:51 am
by Tractorsaw1
4 Replies
168 Views
Last post March 10, 2014, 11:29:40 pm
by farmboy
3 Replies
181 Views
Last post May 12, 2014, 03:36:02 pm
by winland
8 Replies
507 Views
Last post August 03, 2014, 10:06:25 pm
by Al Smith
5 Replies
399 Views
Last post October 23, 2014, 06:53:51 pm
by Cut4fun .
18 Replies
274 Views
Last post March 22, 2015, 09:43:31 pm
by 3000 FPS
1 Replies
115 Views
Last post February 09, 2017, 12:26:19 pm
by Cut4fun .