Author Topic: Dayton 2Z461 17"  (Read 117 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22135
  • Karma: 552
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Dayton 2Z461 17"
« on: November 01, 2015, 01:27:46 pm »
There was a dayton 2z461 I think it was at the place I bought the ole cross cut today. I sent Aaron a pic because I wasnt sure if poulan 361 or 306. 

So is a 361 or 306?

Was only $48 bucks but I'm just not into these.
REDNECK Saw Repair Getter Done

Share on Facebook Share on Twitter


Offline wcorey

  • 3 cube
  • *
  • Posts: 7
  • Karma: 4
Re: Dayton 2Z461 17"
« Reply #1 on: November 01, 2015, 09:19:04 pm »
461=361, 462=306, 463=245

Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4482
  • Karma: 276
  • Location: Carpenter, Wyoming
Re: Dayton 2Z461 17"
« Reply #2 on: November 01, 2015, 10:43:52 pm »
461=361, 462=306, 463=245

I did not know that.  Thanks.
PP 505, 475, 445.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22135
  • Karma: 552
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dayton 2Z461 17"
« Reply #3 on: November 02, 2015, 07:39:12 am »
461=361, 462=306, 463=245

Nice info Thanks.

It was a really clean looking saw. Had it been a 2800 3000 3300 335 3500 365 3750 380 series I would have left with it.
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Dayton 2Z461 17"
« Reply #4 on: November 02, 2015, 03:31:51 pm »
If you see a Dayton branded 4200-8500 series saw that's in similar condition (and for a similar price.......although I'd pay more).........................PLEASE pick it up for me.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline wcorey

  • 3 cube
  • *
  • Posts: 7
  • Karma: 4
Re: Dayton 2Z461 17"
« Reply #5 on: November 02, 2015, 11:21:11 pm »
5.2=4Z252 (I want one too!) or 358.358810 if red.


4.2=(?)7Z627 or 358.358840 if red.



Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Dayton 2Z461 17"
« Reply #6 on: November 03, 2015, 03:46:58 am »
I have the Craftsman red 5.2/30 branded 5200.  Don't have the 4.2/24 or any of the Dayton versions.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

 

Related Topics

  Subject / Started by Replies Last post
35 Replies
1542 Views
Last post August 30, 2016, 02:52:58 pm
by Cut4fun .
2 Replies
167 Views
Last post September 20, 2013, 01:35:26 pm
by doreadeal
57 Replies
624 Views
Last post January 01, 2014, 07:56:48 pm
by Cut4fun .
3 Replies
153 Views
Last post November 22, 2013, 07:23:02 pm
by 3000 FPS
6 Replies
273 Views
Last post November 08, 2014, 09:59:01 pm
by Cut4fun .
11 Replies
247 Views
Last post January 28, 2015, 10:58:19 pm
by Eccentric
7 Replies
480 Views
Last post September 11, 2015, 03:44:31 pm
by Cut4fun .
8 Replies
145 Views
Last post October 09, 2016, 07:08:42 pm
by Cut4fun .
0 Replies
65 Views
Last post June 04, 2018, 07:57:47 am
by Cut4fun
1 Replies
54 Views
Last post May 28, 2020, 09:43:44 pm
by 3000 FPS