Author Topic: Dayton Hotsaw  (Read 153 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22054
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Dayton Hotsaw
« on: November 22, 2013, 03:04:36 pm »
Figure it must be a Poulan, so posted here to share.  Thinking it was just a gag saw with pipe bolted onto the muffler.

http://mansfield.craigslist.org/grd/4207253192.html
REDNECK Saw Repair Getter Done

Share on Facebook Share on Twitter


Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Dayton Hotsaw
« Reply #1 on: November 22, 2013, 03:24:29 pm »
Dayton orange version of a Poulan 306SA.  59cc.  Good saw.  I have a Poulan 245SA in Dayton colors.  He's about $100 overpriced (in my opinion).  I see he put a rebranded Tsumura bar on it.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline neil

  • 5 cube
  • ***
  • Posts: 135
  • Karma: 21
Re: Dayton Hotsaw
« Reply #2 on: November 22, 2013, 03:54:46 pm »
pipe pop riveted to an exhaust,,,, that will fool them. Loose that silly pipe and it will run a bit better.
Must of been half pissed to think that idea up.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4470
  • Karma: 274
  • Location: Carpenter, Wyoming
Re: Dayton Hotsaw
« Reply #3 on: November 22, 2013, 07:23:02 pm »
pipe pop riveted to an exhaust,,,, that will fool them. Loose that silly pipe and it will run a bit better.
Must of been half pissed to think that idea up.


Yea no kidding.   They would have been better off with a stock muffler on it.   But he says it is a gag saw and that is just what they got.

I have a 306A like most Poulan guys do and it is a pretty decent cutting saw in stock form.
PP 505, 475, 445.

 

Related Topics

  Subject / Started by Replies Last post
35 Replies
1522 Views
Last post August 30, 2016, 02:52:58 pm
by Cut4fun .
2 Replies
167 Views
Last post September 20, 2013, 01:35:26 pm
by doreadeal
11 Replies
244 Views
Last post January 28, 2015, 10:58:19 pm
by Eccentric
8 Replies
611 Views
Last post May 23, 2015, 07:04:00 am
by ccicora
6 Replies
112 Views
Last post November 03, 2015, 03:46:58 am
by Eccentric
8 Replies
145 Views
Last post October 09, 2016, 07:08:42 pm
by Cut4fun .
22 Replies
498 Views
Last post August 17, 2017, 07:04:48 pm
by Cut4fun .
0 Replies
64 Views
Last post June 04, 2018, 07:57:47 am
by Cut4fun
4 Replies
238 Views
Last post February 27, 2019, 07:26:55 pm
by Cut4fun
1 Replies
51 Views
Last post May 28, 2020, 09:43:44 pm
by 3000 FPS