Author Topic: Poulan 4218  (Read 1062 times)

0 Members and 0 Guests are viewing this topic.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1146
  • Karma: 135
  • Location: Hayesville, NC
Winner Winner x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20422
  • Karma: 446
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20422
  • Karma: 446
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4218
« Reply #42 on: April 22, 2017, 08:22:43 am »
Sharing info from the CR group - that makes since to what we are seeing on these zama carbs.

Luke a dealer said =  i have found the accelerator pump o ring goes out , but on a poulan it is cheeper to buy a new carb than replace it , the o ring makes them leak air and run lean no matter how you adj it
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20422
  • Karma: 446
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4218
« Reply #43 on: May 24, 2017, 12:33:32 pm »
All for not in the end. Not planning to put any more $ in it. 

Probably just needs a piston kit.  I could clean it up and just rering for my use. But I wouldnt want to sell it that way unless owner fully understood.

So parts saw.

REDNECK Saw Repair Getter Done

Offline countryhog

  • 6 cube
  • ****
  • Posts: 165
  • Karma: 13
  • Location: NW arkansas
Re: Poulan 4218
« Reply #44 on: June 07, 2017, 01:55:32 pm »
So this thing still on the shelf? Got two of em like that. Curious to know how it turned out
now is never here but the past is always present.
semper fi ya'll

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20422
  • Karma: 446
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4218
« Reply #45 on: June 07, 2017, 03:12:06 pm »
So this thing still on the shelf? Got two of em like that. Curious to know how it turned out

Not going to pull to even check to see if piston cylinder will clean up. Not worth my time IMO to just resell it.  Only get $75 for them.

Poulan 4218 etc piston kit  530071883
REDNECK Saw Repair Getter Done

Offline countryhog

  • 6 cube
  • ****
  • Posts: 165
  • Karma: 13
  • Location: NW arkansas
Re: Poulan 4218
« Reply #46 on: June 07, 2017, 10:30:31 pm »
Pretty much why im walking around two of them plus a 2150. All same symptons.
now is never here but the past is always present.
semper fi ya'll

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20422
  • Karma: 446
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4218
« Reply #47 on: September 20, 2018, 11:08:36 am »
The 6pak of Oktoberfest sold me 😋.  But also got a nice pair of husky chaps and a like new 4218 with case for my labor time.  Not bad for tuning and putting a set of seals in a 026.
Oh and sharpen 2 chains.

So all I got is some time in it all.

Hate that gimmick tool less side cover though.  Maybe next owner might want it.

Owner said it didnt want to start. Dumped old coffee looking mix out, put mine in. Used purge bulb to pass new through. 2nd pull started. 

REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
Poulan 415

Started by Cut4fun « 1 2 ... 9 10 » Poulan

93 Replies
2978 Views
Last post November 21, 2018, 12:39:18 pm
by Cut4fun .
Poulan 220

Started by Cut4fun . « 1 2 » Poulan

17 Replies
754 Views
Last post June 17, 2017, 12:25:32 pm
by Cut4fun .
Poulan 365

Started by Cut4fun « 1 2 ... 16 17 » Poulan

169 Replies
4753 Views
Last post January 31, 2018, 07:59:31 pm
by stubnail67
Poulan pro 236

Started by Cut4fun . « 1 2 3 4 5 » Poulan

48 Replies
1487 Views
Last post December 04, 2015, 10:59:11 am
by Cut4fun .
Poulan s-25

Started by Al Smith « 1 2 3 4 5 » Poulan

40 Replies
2536 Views
Last post February 07, 2014, 05:41:44 pm
by Eccentric
4 Replies
435 Views
Last post November 23, 2012, 12:28:15 am
by Andyshine77
23 Replies
826 Views
Last post November 02, 2015, 04:36:50 pm
by Cut4fun .
14 Replies
363 Views
Last post January 18, 2016, 10:16:01 pm
by 3000 FPS
1 Replies
85 Views
Last post July 20, 2016, 02:48:21 pm
by Cut4fun .
2 Replies
150 Views
Last post May 21, 2017, 08:59:45 pm
by Cut4fun .