Author Topic: quad port poulan 445 425 415  (Read 607 times)

0 Members and 0 Guests are viewing this topic.

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 68
  • Information collector
  • Location: Troms, North Norway
Re: finally phew pp445 p+c
« Reply #10 on: March 22, 2014, 09:42:15 pm »
I don't find that odd at all!   ;)


...but this thread really should be in the Partner forum as well as here, as that was the original brand..... ;D


....and remember that all those saws were made at the Husky factory in Sweden, but there was no orange version of any of the models.

That is an interesting point that they made some of these models in Poulan and Jonsered but not in Husqvarna.

I assume Husky regarded their own 272xp and 281/288xp as better saws - and then the 371xp when the P710/PP445 came out.

They likely were right about that.

Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4460
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: finally phew pp445 p+c
« Reply #11 on: March 23, 2014, 12:55:22 am »
I don't find that odd at all!   ;)


...but this thread really should be in the Partner forum as well as here, as that was the original brand..... ;D


....and remember that all those saws were made at the Husky factory in Sweden, but there was no orange version of any of the models.

That is an interesting point that they made some of these models in Poulan and Jonsered but not in Husqvarna.

I assume Husky regarded their own 272xp and 281/288xp as better saws - and then the 371xp when the P710/PP445 came out.

They likely were right about that.

Well not ever owning any of those models in Huskys I would not know.
PP 505, 475, 445.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: finally phew pp445 p+c
« Reply #12 on: March 23, 2014, 04:41:14 am »
I don't find that odd at all!   ;)


...but this thread really should be in the Partner forum as well as here, as that was the original brand..... ;D


....and remember that all those saws were made at the Husky factory in Sweden, but there was no orange version of any of the models.

That is an interesting point that they made some of these models in Poulan and Jonsered but not in Husqvarna.

I assume Husky regarded their own 272xp and 281/288xp as better saws - and then the 371xp when the P710/PP445 came out.

They likely were right about that.

Well not ever owning any of those models in Huskys I would not know.

I've owned/ran 288XP, 272XP, and 372XP Husqvarnas...............but haven't ran those PP saws.  I can saw that there are no flies on those Husky models.  You fellas sure like those PP models.............so they must be pretty damn good too...
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21879
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: quad port poulan 445 425 415
« Reply #13 on: August 28, 2014, 12:10:52 pm »
Bump for member wanting to see difference in quad and dual singles transfers.
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
17 Replies
2733 Views
Last post June 09, 2011, 07:44:08 am
by 05_sprcrw
9 Replies
554 Views
Last post January 31, 2012, 09:28:50 pm
by Al Smith
100 Replies
1752 Views
Last post February 24, 2013, 12:54:05 pm
by jmester
8 Replies
512 Views
Last post April 17, 2013, 07:51:59 pm
by Al Smith
4 Replies
281 Views
Last post July 02, 2013, 09:47:32 pm
by farmboy
8 Replies
380 Views
Last post November 14, 2013, 12:31:50 am
by 3000 FPS
15 Replies
720 Views
Last post July 11, 2014, 11:12:16 pm
by DexterDay
0 Replies
454 Views
Last post April 07, 2016, 01:41:04 pm
by Cut4fun .
4 Replies
259 Views
Last post April 18, 2018, 01:10:06 am
by 660magnum
3 Replies
22 Views
Last post June 28, 2020, 07:36:32 am
by Cut4fun