Author Topic: Poulan carb fix HDA 164 NLA?  (Read 1992 times)

0 Members and 1 Guest are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan carb fix HDA 164 NLA?
« Reply #60 on: July 15, 2014, 06:21:40 am »
You guys have any luck finding those nozzle type check valves?  I may have to rehab an HDA164 very soon....
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline dowdy41

  • pruner
  • *
  • Posts: 3
  • Karma: 1
Re: Poulan carb fix HDA 164 NLA?
« Reply #61 on: July 15, 2014, 01:45:45 pm »
You guys have any luck finding those nozzle type check valves?

Not at all.
1. Crab's Wicker - Lever and Switch
2. Flux Rod - Spring and Switch
3. Twist - Screw
4. ChIP Steak - Fuel Line
5. Adapting - Fitting
6. Conical Provisions - Assy--Fuel Cap

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22054
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan carb fix HDA 164 NLA?
« Reply #62 on: July 15, 2014, 02:17:00 pm »
What was the part number you guys were looking for?    IPL  http://wem.walbro.com/walbro/product.asp?CategoryName=61cc&Series=HDA&partnum=HDA-164-1&GroupName=Chain%20Saw&FamilyName=POULAN

If this is it dont show available anymore.  19    Nozzle Assembly - Check Valve    86-654
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22054
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan carb fix HDA 164 NLA?
« Reply #64 on: July 15, 2014, 03:21:51 pm »
Yep.  #19.  Walbro 86-654.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline mowertech

  • 5 cube
  • ***
  • Posts: 87
  • Karma: 3
    • Online  Store  Site  Obsolete  Homelite  Super Store
Re: Poulan carb fix HDA 164 NLA?
« Reply #65 on: July 17, 2014, 02:53:12 pm »
Kevin  normally  when a  parts  lookup  says  call  us  that  normally  means  NLA   alot of dealers  order  parts  as  needed  basis  keeps  down the  overhead
For your  Obsolete Homelite  , McCulloch , Echo,
Poulan  Parts  visit us at  http://www.smallenginechainsawparts.com

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22054
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan carb fix HDA 164 NLA?
« Reply #66 on: July 24, 2016, 09:10:06 pm »
Think I may have my 1st 164 carb issue.  Just as Aaron described it.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22054
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan carb fix HDA 164 NLA?
« Reply #67 on: August 01, 2016, 11:04:23 am »
The check valve was leaking in my 164. The 137 works great on the saw. If you dont mind a smaller carb the 49 will work too.
REDNECK Saw Repair Getter Done

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4470
  • Karma: 274
  • Location: Carpenter, Wyoming
Re: Poulan carb fix HDA 164 NLA?
« Reply #68 on: August 01, 2016, 10:02:15 pm »
I have not run into a bad one yet.   But since the 137 is no longer, we just use what we have.
PP 505, 475, 445.
Agree Agree x 1 View List

 

Related Topics

  Subject / Started by Replies Last post
36 Replies
907 Views
Last post July 16, 2014, 07:18:19 pm
by Cut4fun
35 Replies
1126 Views
Last post November 11, 2016, 11:28:35 pm
by pete
Poulan 3450 Carb issues

Started by rockfishon « 1 2 ... 7 8 » Poulan

77 Replies
1091 Views
Last post August 27, 2015, 07:55:47 pm
by Eccentric
3 Replies
4934 Views
Last post December 03, 2014, 04:08:24 pm
by Windy_Acres
3 Replies
272 Views
Last post June 30, 2015, 07:11:44 pm
by Jason K
15 Replies
607 Views
Last post September 09, 2015, 10:06:43 pm
by Eccentric
5 Replies
172 Views
Last post November 18, 2015, 12:19:22 pm
by Cut4fun .
5 Replies
141 Views
Last post December 11, 2015, 05:11:29 pm
by jrbarba
5 Replies
1293 Views
Last post February 23, 2016, 11:10:39 am
by countryhog
3 Replies
336 Views
Last post July 13, 2016, 02:28:19 am
by Hoggwood