Author Topic: NLA Poulan Jonsered parts 415 425 445 475 505 2077 2083  (Read 745 times)

0 Members and 1 Guest are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 215
  • Magnesium and Iron.
  • Location: Northern California.
Hi I'm looking for a clutch cover for my jonsered 2083. Is there a husky or other available part that will fit?
Thanks will


Sent from my iPhone using Tapatalk

You can cut and make a husky 272 268 etc fit.  In thread here where I did one and Roger.

2077 2083 415 425 445 505 475 all fit yours.

Came across better pics.

Using 272 268 266 61 66 etc  for make do covers.





Kevin do you still have the chainbrake lever and other chainbrake parts from that Husky clutch cover that you modified here?  I could sure use them....
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 3906
  • Karma: 141
  • OHIO REDNECK

Kevin do you still have the chainbrake lever and other chainbrake parts from that Husky clutch cover that you modified here?  I could sure use them....

Gave all the parts to Mitch mweba.  He had helped me out on hard to find parts in past for other folks saws I have worked on.  So I donated to his stash. Might try contacting him.
REDNECK Saw Repair

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 215
  • Magnesium and Iron.
  • Location: Northern California.

Kevin do you still have the chainbrake lever and other chainbrake parts from that Husky clutch cover that you modified here?  I could sure use them....

Gave all the parts to Mitch mweba.  He had helped me out on hard to find parts in past for other folks saws I have worked on.  So I donated to his stash. Might try contacting him.

I'll contact Mitch.  He's a good guy.  Haven't talked to him in a while.....
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21039
  • Karma: 468
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
When I get that bare 475 crankcase I will try out the newer oiler wing gear on it.

Good let me know how that works.

I received the 475 crankcase today. Was suppose to be a good crankcase assembly.
Took me all of 1 second to see the big end bearing was out and could move up down. 

But I do think the idea will work after test fitting them today Roger.
REDNECK Saw Repair Getter Done

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4313
  • Karma: 257
  • Location: Carpenter, Wyoming
Ok Kevin thanks.
PP 505, 475, 445.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21039
  • Karma: 468
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Did somebody say clutch covers.
I was taking a pic of other parts in the micro series and just happen to have 1 of my bins of this series of stuff laid out looking for my oiler parts to test fit.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21039
  • Karma: 468
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
6 base gaskets http://www.ebay.com/itm/Jonsered-2077-2083-Poulan-Pro-PP475-505-Chainsaw-NOS-Cylinder-Base-Gasket-/301682732740?pt=LH_DefaultDomain_0&hash=item463db12ec4

When you could get them from Ordertee 503428601 GASKET-CYLIND USD 3.58  plus 7-8 shipping.  NLA This product is not available in the requested quantity. 1 of the items will be backordered.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21039
  • Karma: 468
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
After posting above I checked my stock of base gaskets. Being I am back to using gaskets on builds I only had 2 left.

I waited till above ended to let you folks buy any if needed. After it ended and relisted I made a offer for all listed and have 6 more to set back (when they get here).   Least we will know where they are at, like the NLA 335 etc air filters buy in the past.  8)
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21039
  • Karma: 468
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
I notice folks always looking for these. The right side handle to cylinder AV anti vibe. They come in rubber early and coil spring later. 

Still can be bought if you just look. ;)  This info below came from Ordertree.com

501269702 standard rubber  $7.51

504125014 heavy duty rubber  $27.97

503514802 spring isolator   $10.49

   
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
27 Replies
691 Views
Last post February 22, 2017, 07:26:04 pm
by Cut4fun .
12 Replies
733 Views
Last post December 06, 2013, 02:16:11 pm
by David Young
5 Replies
276 Views
Last post August 24, 2014, 10:40:36 am
by Cut4fun
4 Replies
153 Views
Last post October 19, 2018, 03:18:46 pm
by Cut4fun .
1 Replies
369 Views
Last post January 14, 2017, 02:17:56 pm
by Cut4fun .
6 Replies
143 Views
Last post July 22, 2017, 12:54:36 pm
by 3000 FPS
15 Replies
247 Views
Last post May 07, 2019, 04:48:06 pm
by Cut4fun .
15 Replies
132 Views
Last post November 16, 2018, 02:56:14 pm
by Cut4fun .
3 Replies
72 Views
Last post October 23, 2018, 11:16:06 am
by Cut4fun .
1 Replies
78 Views
Last post December 13, 2018, 04:19:47 pm
by Cut4fun .