Author Topic: Poulan 2000  (Read 194 times)

0 Members and 0 Guests are viewing this topic.

Offline petelg

  • pruner
  • *
  • Posts: 2
  • Karma: 0
Poulan 2000
« on: June 14, 2013, 03:58:13 pm »
Hi... Just joined the forum for obvious reasons.. ;D..I'm a terrible mechanic and I have a Poulan 2000 that has been sitting on the shelf in the shop for a couple of years without being started..In VERY lamen terms can anyone walk me thru getting this thing to running? Any help would be appreciated...Pete :-[

Share on Facebook Share on Twitter


Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: Poulan 2000
« Reply #1 on: June 14, 2013, 05:55:03 pm »
Welcome

Dump the old fuel out and start with new fuel

It should start right up?

Typically after you run it a couple days, it will get to where you can not adjust the carburetor?

It is then time for a new metering valve diaphragm in the carb.

If it doesn't start right up for you, get back on here.
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22582
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 2000
« Reply #2 on: June 14, 2013, 06:20:20 pm »
Bought one of those new in 1994.  1 carb kit and fuel line replacement so far.   Also had a coil go out once.

OEM fuel lines tend to dry rot and crank.  Look it over (fuel line inside handle, into tank and air filter area to carb) and fuel up like 660mag said.

 Good little saws if you can stand the vibrations on the hands.

Poulan 1800 2000 IPL   http://www.poulan.com/ddoc/POUI/POUI1996_USen/POUI1996_USen__530083694.pdf
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
4 Replies
639 Views
Last post November 23, 2012, 12:28:15 am
by Andyshine77
1 Replies
46 Views
Last post March 13, 2014, 11:01:01 pm
by bustedknuckles
9 Replies
555 Views
Last post August 04, 2014, 03:06:33 pm
by ChipsAhoy
2 Replies
30 Views
Last post June 01, 2015, 06:50:41 am
by Jason K
24 Replies
633 Views
Last post June 30, 2015, 12:02:15 pm
by Jason K
8 Replies
155 Views
Last post June 11, 2015, 11:48:52 pm
by 660magnum
5 Replies
142 Views
Last post February 24, 2019, 06:10:25 pm
by Cut4fun .
3 Replies
32 Views
Last post June 08, 2021, 02:32:02 pm
by Cut4fun .
0 Replies
14 Views
Last post June 08, 2021, 06:55:55 am
by Cut4fun .
0 Replies
107 Views
Last post June 08, 2021, 07:18:22 am
by Cut4fun