Author Topic: poulan 2050 carb linkage  (Read 958 times)

0 Members and 0 Guests are viewing this topic.

Offline pete

  • Piped Saw
  • *****
  • Posts: 499
  • Karma: 37
poulan 2050 carb linkage
« on: May 27, 2013, 07:29:37 am »
Hi guys can someone please post a pic or 3 of the poulan 2050 carb to throttle linkage    Linkage

I take saws to work and let the boys from our special education unit dismantle and clean them up under supervision.  These guys are like normal lads when it comes to tools and motors so many basket case saws and brushcutters go in for them to pull apart..   Unfortunately sometimes one of my saws gets mistaken for a basket case  as has happened here I had this saw pulled down to refit a carb kit but had to wait for the carb mating gasket to come in the post
One of the lads informed me he had cleaned my saw for me I thanked him and then found out it was a good one that I was fixing   He was able to show me where all the screws and bits were but the throttle linkage is long gone
So please a pic of the part and possibly one in situ would be great Or if someone has one to sell let me know Only snag is I am in oz cheers

Share on Facebook Share on Twitter


Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4548
  • Karma: 292
  • Location: Carpenter, Wyoming
Re: poulan 2050 carb linkage
« Reply #1 on: May 28, 2013, 02:43:36 am »
I went to google and typed in, Poulan 2050 ipl, and the third hit on the list shows the parts list with a picture of the linkage.  Sorry but I do not have a saw to take a picture of.
PP 505, 475, 445.

Offline pete

  • Piped Saw
  • *****
  • Posts: 499
  • Karma: 37
Re: poulan 2050 carb linkage
« Reply #2 on: May 28, 2013, 06:24:39 am »
Thanks very much will just finish reading today's post's and will head to google

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22584
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: poulan 2050 carb linkage
« Reply #3 on: May 28, 2013, 02:06:34 pm »
I think I have a 1950 or 2050 and a 2375 on the shelf. What pics you needing?

I probably have a linkage you could have. You pay shipping to Oz tough.  :o
REDNECK Saw Repair Getter Done

Offline pete

  • Piped Saw
  • *****
  • Posts: 499
  • Karma: 37
Re: poulan 2050 carb linkage
« Reply #4 on: May 29, 2013, 06:14:44 am »
What would shipping be   I have sent an email to the company with the ipl they have the throttle wire for 1.25   so I dont know wether they will answer me or not.  If I dont hear from them in a couple of days I would happily go for it.  like to get this project finished thanks

Offline pete

  • Piped Saw
  • *****
  • Posts: 499
  • Karma: 37
Re: poulan 2050 carb linkage
« Reply #5 on: May 29, 2013, 06:16:14 am »
 Sorry forgot to add a couple of pics of the airbox interior with the linkage hooked to the carb would be great thanks

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22584
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22584
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: poulan 2050 carb linkage
« Reply #7 on: May 30, 2013, 02:43:55 pm »
Rutroa SOL  :-[ :-[  Must have used the last linkages I had on the heinz 57 rebuilds I did last time or 2.  Sorry none found.

Pics of a 1950 linkage runs on flywheel side on this one.  I have also seen linkage on other poulans on right side clutch side.



REDNECK Saw Repair Getter Done

Offline pete

  • Piped Saw
  • *****
  • Posts: 499
  • Karma: 37
Re: poulan 2050 carb linkage
« Reply #8 on: May 30, 2013, 07:56:58 pm »
Pics are good thanks 2050 runs flywheel side as well thanks  Most of the shippers won't ship to oz order is too small

Offline pete

  • Piped Saw
  • *****
  • Posts: 499
  • Karma: 37
Re: poulan 2050 carb linkage
« Reply #9 on: June 01, 2013, 02:04:33 am »
 Got a reply todayy part cost 1dollar 25 cents postage   21 to35 days 16.50
7 to 14 days 35.00  and it gets worse from there  thought I was on a winner today traded some stihl stuff  for dead mac gear Had the right carb but had a cable linkage

So if someone can help let me know

 

Related Topics

  Subject / Started by Replies Last post
poulan 2050

Started by pete Poulan

8 Replies
351 Views
Last post November 20, 2012, 07:49:28 am
by brokenbudget
1 Replies
187 Views
Last post March 31, 2013, 09:51:03 pm
by Remington
6 Replies
359 Views
Last post September 26, 2013, 03:16:07 pm
by sharkey
68 Replies
2173 Views
Last post August 01, 2016, 10:02:15 pm
by 3000 FPS
15 Replies
892 Views
Last post May 01, 2014, 10:58:35 am
by 660magnum
Poulan 3450 Carb issues

Started by rockfishon « 1 2 ... 7 8 » Poulan

77 Replies
1293 Views
Last post August 27, 2015, 07:55:47 pm
by Eccentric
3 Replies
6692 Views
Last post December 03, 2014, 04:08:24 pm
by Windy_Acres
5 Replies
145 Views
Last post May 04, 2015, 11:29:40 pm
by 3000 FPS
15 Replies
707 Views
Last post September 09, 2015, 10:06:43 pm
by Eccentric
3 Replies
48 Views
Last post July 20, 2021, 02:11:10 pm
by John Mc