Author Topic: Poulan 2150 fuel line routing  (Read 711 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Poulan 2150 fuel line routing
« on: April 18, 2014, 12:39:10 pm »
Another little poulan came in and it wont leave  :'(   = friend moved up to a 036 and is all smiles.   So now I have a 1950 2150 2375 to do fuel lines and carbs on.  All start just need the typical stuff on these.
REDNECK Saw Repair Getter Done

Share on Facebook Share on Twitter


Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4459
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: Poulan 2150
« Reply #1 on: April 18, 2014, 04:12:03 pm »
We'll is that a good thing or bad.

I was out bucking and splitting today.   I was using my 3700.    That saw just makes me smile.
PP 505, 475, 445.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 2150
« Reply #2 on: April 18, 2014, 05:01:33 pm »
Any saw is a good thing I guess, especially when they come to you on the cheap hand delivered  (traded my labor sharpening some chains). 

I'm just going to set it on the shelf on the way way back list of saws to do.
REDNECK Saw Repair Getter Done

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4044
  • Karma: 159
  • OHIO REDNECK
Re: Poulan 2150
« Reply #3 on: April 19, 2014, 08:19:28 pm »
After doing wheel tire swaps and oil changes today. I was able to look the 2150 over.  Has the throttle lock on top of rear handle like I like  on these.
Couldnt have been used much and just what I thought IMO. Fuel filter with broken line attached rattling around in tank.  Then found the little black connector in tank too.  Guess need to see whats missing there.
All 4 recoil bolts missing, but he told me he had took those for something. Fills like good psi pulling over.

Weird thing I thought it had a chain brake clutch cover like on the 1950 and 2375 WT. Turns out it was a fake handle and just a hand guard that looks like a brake handle. Attached or molded into handle somehow. Didnt look real close at that.
REDNECK Saw Repair

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 2150
« Reply #4 on: July 29, 2014, 02:47:29 pm »
Poulan 2150.  Just ran all  new lines 3 and left stock sizes for whoever ends up  with it down the road. 

I used that tygon 1100 again and that line gets really stiff just setting on the shelf.  Really like working with the tygon 4040 better.  1100 for the bigger lines and 4040 for the small one.

Tried to get some good pics of the fuel line routing. Will upload in a bit.

Also after getting it altogether the primer bulb pushed right through. So I just pulled and plocked off ends to start etc.  Then since I didnt have a spare primer bulb  in screw on style, I pulled one from the old ryobi tiller that was clip in style and used it for now.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 2150 fuel line routing
« Reply #5 on: July 29, 2014, 03:03:12 pm »
This was the fuel line routing on this poulan 2150.  Marked them A B C and at both end areas to show routing.

The 2375 on the bench the C line was on the left side of carb.

Top right red A didnt show up to well.  :(



REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan 2150 fuel line routing
« Reply #6 on: July 29, 2014, 03:52:42 pm »
Nice illustration Kevin. 
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 2150 fuel line routing
« Reply #7 on: July 29, 2014, 04:10:18 pm »
Nice illustration Kevin. 

Thanks just trying to make things easier for future folks.

I get confused just looking and trying to remember myself when removed.  Can only imagine the guys doing it the 1st time.

REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 2150 fuel line routing
« Reply #8 on: July 29, 2014, 04:34:57 pm »
OK the older 2375 that is letter C line on left side of carb.  I will correct my above post too.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 2150 fuel line routing
« Reply #9 on: July 29, 2014, 06:21:40 pm »
Aint that the way it is  :D. Everything checks out, oiler and all. Out making some test cuts and notice chain is dry. Go back in pull bar and chain and start up. Nope no oil output.  :P

Pull everything from inside tank out to oiler. Oil pump gear looks good etc. Cleaned up blew out hoses,put back together and all good again.   ::)

Noticed the sticker on this 2150 is dated 1995 and the 2375 has a sticker of 2003.  That must explain some different fasteners used on the 2150  ( like straight slot for top cover fasteners )and some others I noticed or someone has changed them over the years.
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
18 Replies
4318 Views
Last post March 26, 2017, 05:46:32 pm
by Cut4fun .
2 Replies
421 Views
Last post March 28, 2012, 12:27:35 pm
by nmurph
11 Replies
838 Views
Last post October 30, 2016, 09:16:26 am
by Sty57
6 Replies
633 Views
Last post January 11, 2013, 05:01:34 pm
by Cut4fun .
2 Replies
388 Views
Last post August 26, 2013, 01:39:22 pm
by Bluegill
15 Replies
1549 Views
Last post April 30, 2014, 11:58:07 pm
by Eccentric
25 Replies
340 Views
Last post November 07, 2015, 07:25:01 pm
by treeslayer2003
5 Replies
168 Views
Last post November 18, 2015, 12:19:22 pm
by Cut4fun .
11 Replies
530 Views
Last post June 08, 2016, 01:58:07 pm
by Cut4fun
12 Replies
165 Views
Last post June 10, 2019, 10:46:53 am
by AmericanPsycho