« previous next »
Pages: 1 2 [3] 4   Go Down

Author Topic: Poulan 2150 fuel line routing  (Read 2586 times)

0 Members and 3 Guests are viewing this topic.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4708
  • Karma: 320
  • Location: Carpenter, Wyoming
Re: Poulan 2150 fuel line routing
« Reply #20 on: November 18, 2015, 05:23:16 pm »
I think it is A the small line that has the filter on it.   When you pump the primer bulb you should see fuel in the line returning to the fuel tank.   That line has no filter which means the other line going into the tank does have a filter.
Logged
PP 505, 475, 445.

Offline leec

  • 6 cube
  • ****
  • Posts: 264
  • Karma: 14
  • Location: Huntsville, Ontario
Re: Poulan 2150 fuel line routing
« Reply #21 on: November 21, 2015, 04:13:23 pm »
Quote from: Cut4fun . on November 18, 2015, 12:21:47 pm
Quote from: Drew_Uth on November 18, 2015, 08:33:54 am
Pretty sure the filter goes on B.  A goes to primer.

Fuel lines shown is correct on a running saw above. A does not go to primer. It is as shown.

Just cant remember which line had the fuel filter at end inside tank. All my saws like this are gone.
I thinlk it is B that gets the filter inside the tank.  The pic is confusing as A appears to go into the tank beside B but it just loops round behind the carb. A is the return line from the purge effort.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23987
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 2150 fuel line routing
« Reply #22 on: November 21, 2015, 05:19:56 pm »
Does the new strato poulan 3314 have this set up?  I just got one in the other day and can check the A B routing.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23987
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 2150 fuel line routing
« Reply #23 on: November 21, 2015, 05:20:46 pm »
Matter fact I will walk out and check. it is halftime.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23987
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 2150 fuel line routing
« Reply #24 on: November 21, 2015, 05:28:16 pm »
Quote from: leec on November 21, 2015, 04:13:23 pm
Quote from: Cut4fun . on November 18, 2015, 12:21:47 pm
Quote from: Drew_Uth on November 18, 2015, 08:33:54 am
Pretty sure the filter goes on B.  A goes to primer.

Fuel lines shown is correct on a running saw above. A does not go to primer. It is as shown.

Just cant remember which line had the fuel filter at end inside tank. All my saws like this are gone.
I thinlk it is B that gets the filter inside the tank.  The pic is confusing as A appears to go into the tank beside B but it just loops round behind the carb. A is the return line from the purge effort.
Quote from: Cut4fun . on November 17, 2015, 08:28:42 pm
my WAG A   correct me if I am wrong someone. been awhile now and memory not sharp.
Quote from: 3000 FPS on November 18, 2015, 05:23:16 pm
I think it is A the small line that has the filter on it.   When you pump the primer bulb you should see fuel in the line returning to the fuel tank.   That line has no filter which means the other line going into the tank does have a filter.

Confirmed now.

Like me and Roger said. 

A is attached to fuel filter. 

B is the return line from primer back to tank.
Logged

Offline leec

  • 6 cube
  • ****
  • Posts: 264
  • Karma: 14
  • Location: Huntsville, Ontario
Re: Poulan 2150 fuel line routing
« Reply #25 on: November 23, 2015, 08:35:41 am »
Just working on a 2150 and the filter was on B although line A was also long enough in the tank to be the fuel line. Line B in my saw had a joiner on the line just inside the tank as if it was acting as a seal pulled up into the line opening in the tank case.  P&C good on the 2150.  I find these to be better saws than the later ones. The IPLs are useless.

I also picked up a Stratos saw at the same time but it runs so I can just follow the existing lines
Logged

Offline thousandbuckle

  • 3 cube
  • *
  • Posts: 5
  • Karma: 2
Re: Poulan 2150 fuel line routing
« Reply #26 on: November 23, 2015, 08:56:32 am »
I hooked up the fuel filter to line A the small line coming out of the left side of the tank into the top connector on the carb. The lower carb connector went to the short nipple on the primer bulb. Then the larger hose from the longer nipple of the the primer bulb goes back into the tank on the right hand side. With this setup pumping the primer bulb was sucking fuel into line A through the filter and returning it through line B with no filter and it runs perfect.

Sent from my SAMSUNG-SM-G900A using Tapatalk

Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23987
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 2150 fuel line routing
« Reply #27 on: November 23, 2015, 12:45:21 pm »
leec Line B coming from the primer to tank has that joiner. It is suppose to end there inside tank. No line attached. Someone used the wrong side IMO.
Logged

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4708
  • Karma: 320
  • Location: Carpenter, Wyoming
Re: Poulan 2150 fuel line routing
« Reply #28 on: November 23, 2015, 09:53:20 pm »
Quote from: thousandbuckle on November 23, 2015, 08:56:32 am
I hooked up the fuel filter to line A the small line coming out of the left side of the tank into the top connector on the carb. The lower carb connector went to the short nipple on the primer bulb. Then the larger hose from the longer nipple of the the primer bulb goes back into the tank on the right hand side. With this setup pumping the primer bulb was sucking fuel into line A through the filter and returning it through line B with no filter and it runs perfect.

Sent from my SAMSUNG-SM-G900A using Tapatalk


Thanks for getting back and letting us know.    Good to hear you got it going.
Logged
PP 505, 475, 445.

Offline leec

  • 6 cube
  • ****
  • Posts: 264
  • Karma: 14
  • Location: Huntsville, Ontario
Re: Poulan 2150 fuel line routing
« Reply #29 on: November 24, 2015, 08:39:03 am »
Quote from: leec on November 21, 2015, 04:13:23 pm
Quote from: Cut4fun . on November 18, 2015, 12:21:47 pm
Quote from: Drew_Uth on November 18, 2015, 08:33:54 am
Pretty sure the filter goes on B.  A goes to primer.



Just cant remember which line had the fuel filter at end inside tank. All my saws like this are gone.
I thinlk it is B that gets the filter inside the tank.  The pic is confusing as A appears to go into the tank beside B but it just loops round behind the carb. A is the return line from the purge effort.
Quote
author=Cut4fun ]
Fuel lines shown is correct on a running saw above. A does not go to primer. It is as shown.

I was wrong.  Fuel line is A the smaller of the two lines and the filter attaches to it.   My saw had the filter on B so no wonder it would not run.  Also thanks to the photos I got the carb linkage back on correctly.  Just need to find the right size lines in my swag and it will be done.  "An other fine mess you've gotten us into Ollie"

Thanks for the help!
Logged
Pages: 1 2 [3] 4   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
2 Replies
859 Views 		Last post March 28, 2012, 12:27:35 pm
by nmurph
11 Replies
2027 Views 		Last post October 30, 2016, 09:16:26 am
by Sty57
6 Replies
1591 Views 		Last post January 11, 2013, 05:01:34 pm
by Cut4fun .
2 Replies
813 Views 		Last post August 26, 2013, 01:39:22 pm
by Bluegill
163 Replies
9666 Views 		Last post August 01, 2024, 07:52:16 am
by Cut4fun .
15 Replies
6153 Views 		Last post April 30, 2014, 11:58:07 pm
by Eccentric
25 Replies
1574 Views 		Last post November 07, 2015, 07:25:01 pm
by treeslayer2003
5 Replies
824 Views 		Last post November 18, 2015, 12:19:22 pm
by Cut4fun .
11 Replies
1366 Views 		Last post June 08, 2016, 01:58:07 pm
by Cut4fun
12 Replies
1095 Views 		Last post June 10, 2019, 10:46:53 am
by AmericanPsycho