Author Topic: Poulan 315 50th anniversary edition  (Read 742 times)

0 Members and 0 Guests are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan 315 50th anniversary edition
« Reply #10 on: February 14, 2015, 05:07:13 pm »
I have not seen a 310 or 315 before.    The 310 looks a lot like a 295.

Yep.  They're both in the same series as the 2500/2700/2900/PP255/PP295/PP4620/etc.  Just a different engine (with a larger bore) under the hood.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.
Informative Informative x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22009
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 315 50th anniversary edition
« Reply #11 on: February 14, 2015, 05:13:09 pm »
1 on feebay / 1 on AS
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan 315 50th anniversary edition
« Reply #12 on: February 14, 2015, 05:16:49 pm »
Ah 10-4.  Hadn't seen the ebay saw.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan 315 50th anniversary edition
« Reply #13 on: February 14, 2015, 05:22:06 pm »
Found it.  He wants a lot for shipping.....................most likely because of the hard case.

http://www.ebay.com/itm/Poulan-Pro-315-50th-Anniversary-Chain-Saw-/121569015480?pt=LH_DefaultDomain_0&hash=item1c4e13f6b8
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline ChipsFlyin

  • 4 cube
  • **
  • Posts: 26
  • Karma: 11
  • Location: Pittsburgh, PA
Re: Poulan 315 50th anniversary edition
« Reply #14 on: February 17, 2015, 05:49:19 pm »
I'm also curious how the 49cc clam shells perform.   I know that the Poulan 3000, 3100 (Craftsman 358.356070) PP305 49ccer's are solid, strong runners that hold their own very well.
Mark

Poulan 2000, 2300 CVA, S25CVA, Craftsman 2.3 PS/VL (S25CVA), Craftsman 3.0/ Poulan 3000, Craftsman 3.3/ Poulan 3300 (2), Poulan 3450,  Poulan 3400, Wright 141A/401A,  Olympyk 284, Homelite Super XL 925,
Husqvarna 288XP
Like Like x 1 View List

Offline dougand3

  • pruner
  • *
  • Posts: 4
  • Karma: 2
Re: Poulan 315 50th anniversary edition
« Reply #15 on: May 27, 2018, 10:20:32 pm »
Thread Revival!
I got a PP 315 50th Ann in a lot of saws I bought. Seems like it will be a competent saw. Donít know too much yet - need new clutch, sprocket and starter pulley.
How do they pull 18ď .325?
Thinking about trying 3/8LP. It has a K041 bar but bet A041 will work.
Clutch drum is 67mm OD and bearing is 13mm OD. Seeing if I can find a rim sprocket like that to take a 3/8LP rim.
Like Like x 2 View List

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4468
  • Karma: 274
  • Location: Carpenter, Wyoming
Re: Poulan 315 50th anniversary edition
« Reply #16 on: May 28, 2018, 09:20:31 pm »
When you get ur done post a picture so we can see how it turned out.
PP 505, 475, 445.
Agree Agree x 1 View List

Offline dougand3

  • pruner
  • *
  • Posts: 4
  • Karma: 2
Re: Poulan 315 50th anniversary edition
« Reply #17 on: May 29, 2018, 09:38:05 am »
Sure will, 3000 FPS.
Like Like x 2 View List

Offline dougand3

  • pruner
  • *
  • Posts: 4
  • Karma: 2
Re: Poulan 315 50th anniversary edition
« Reply #18 on: June 04, 2018, 10:31:54 pm »
Got clutch, drum and pulley on. Looks pretty good except clutch cover has bubbly melt on it - bet somebody pizz reved with brake on. Runs pretty good - will get into wood next week.

[ Guests cannot view attachments ]

[ Guests cannot view attachments ]
Like Like x 2 View List

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4468
  • Karma: 274
  • Location: Carpenter, Wyoming
Re: Poulan 315 50th anniversary edition
« Reply #19 on: June 04, 2018, 11:29:13 pm »
Nice saw dougand3.   It has the red throttle control setup on it.   I like that look.   
PP 505, 475, 445.

 

Related Topics

  Subject / Started by Replies Last post
Poulan 425

Started by Cut4fun « 1 2 » Poulan

15 Replies
1092 Views
Last post March 18, 2014, 02:19:35 pm
by Cut4fun .
17 Replies
769 Views
Last post May 24, 2017, 06:52:22 pm
by 3000 FPS
Poulan 445

Started by 3000 FPS « 1 2 ... 18 19 » Poulan

181 Replies
4584 Views
Last post August 01, 2020, 08:05:18 am
by Cut4fun
7 Replies
521 Views
Last post April 13, 2014, 08:11:42 pm
by Cut4fun .
0 Replies
192 Views
Last post October 02, 2012, 11:36:18 am
by mweba
4 Replies
549 Views
Last post November 23, 2012, 12:28:15 am
by Andyshine77
23 Replies
1227 Views
Last post November 02, 2015, 04:36:50 pm
by Cut4fun .
11 Replies
1006 Views
Last post October 06, 2013, 10:12:00 pm
by stihls066
3 Replies
139 Views
Last post September 25, 2017, 08:10:47 am
by pete
0 Replies
166 Views
Last post October 21, 2017, 10:25:14 pm
by Cut4fun .