« previous next »
Pages: [1]   Go Down

Author Topic: Poulan 3300 carb adjustments  (Read 1725 times)

0 Members and 0 Guests are viewing this topic.

Offline Jim_I

  • 4 cube
  • **
  • Posts: 27
  • Karma: 1
Poulan 3300 carb adjustments
« on: July 12, 2016, 11:04:23 am »
I just acquired a Poulan 3300.  Saw runs okay, but the carb adjustments have been messed with (it smokes a lot).  Been looking for a shop manual on line and can't find one for free.  Anyone know what the factory carb settings are?  Or can you point me in the direction of a free shop manual that I can download?  Thanks.
Logged

Share on Bluesky Share on Facebook

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24222
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3300 carb adjustments
« Reply #1 on: July 12, 2016, 12:01:15 pm »
Never seen a manual for one other then IPL.  Carb is normal adjustments.  Start 1 to 1.25 out from lightly seated sometimes 1.5 out to be on rich side.

http://www.madsens1.com/sawtune.htm

Should have a walbro carb HDA-49. The complete kit is K22-HDA.

Make sure you check your impulse line and fuel line for cracks.
Logged

Offline Jim_I

  • 4 cube
  • **
  • Posts: 27
  • Karma: 1
Re: Poulan 3300 carb adjustments
« Reply #2 on: July 12, 2016, 02:14:42 pm »
Thanks.  Haven't had it apart yet.  The H and L adjustment screws were out about 3 turns.  Not normal for what I'm used to, but I never had a Poulan before. 
Logged

Offline Hoggwood

  • 4 cube
  • **
  • Posts: 65
  • Karma: 19
Re: Poulan 3300 carb adjustments
« Reply #3 on: July 13, 2016, 02:28:19 am »
Factory called for 1 on both L and H.  L was to be set using the lean and rich drop off points.  Mid point between and then a bit richer is getting close.  I find the HDA-49's on my 3000's are closer to 1 1/4 on the L and and a tad leaner than 1 on the H. 

As was mentioned, the factory impulse lines need checking.  The material for the line did not stand up to the heat at the cylinder base.  I have not seen one that hadn't become brittle.  Check the carb intake boot carefully for cracks as well. 
Logged
Like Like x 1 View List
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
Poulan 3300

Started by Cut4fun « 1 2 ... 5 6 » Poulan

58 Replies
7551 Views 		Last post September 20, 2024, 02:30:50 pm
by Cut4fun
1 Replies
1130 Views 		Last post December 11, 2012, 04:27:45 pm
by Cut4fun .
44 Replies
4642 Views 		Last post July 26, 2015, 05:45:30 pm
by Cut4fun .
3 Replies
2019 Views 		Last post February 03, 2013, 06:33:10 pm
by 660magnum
6 Replies
1199 Views 		Last post September 12, 2014, 01:39:38 pm
by Cut4fun .
11 Replies
1683 Views 		Last post January 06, 2015, 01:06:57 pm
by Cut4fun .
11 Replies
2115 Views 		Last post June 08, 2016, 01:58:07 pm
by Cut4fun
2 Replies
2063 Views 		Last post September 21, 2017, 10:17:09 am
by hillpc
0 Replies
362 Views 		Last post February 13, 2021, 08:08:23 am
by Cut4fun
1 Replies
656 Views 		Last post June 02, 2022, 04:35:23 pm
by ssidwell