Author Topic: Poulan 3314  (Read 431 times)

0 Members and 0 Guests are viewing this topic.

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 327
  • Karma: 28
Re: Poulan 3314
« Reply #10 on: November 22, 2015, 11:49:41 pm »
had one in other day everything on it wore out except engine. recoil spool ,chain sprocket, bar and chain, carb rebuild fuel lines. stripped out one that was like new but had been straight gassed. put it back to work. owner was tickled to get it back because it was a workhorse.

Offline leec

  • 6 cube
  • ****
  • Posts: 262
  • Karma: 13
  • Location: Huntsville, Ontario
Re: Poulan 3314
« Reply #11 on: November 23, 2015, 08:41:06 am »
I find these 3314 just sound awful.  The mufflers must be very restrictive.  Ignition must be quite advanced as they always want to take off your fingers if you are not committed to your pull.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20431
  • Karma: 446
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3314
« Reply #12 on: November 28, 2015, 11:11:40 am »
Come on.  That is bad.   They need to find a new 2 cycle mechanic.   The very first thing I do when at work is to pull the gas cap and take a whiff.   If slightly suspect I toss the fuel.   Don't you wish they were all that hard.

The owner told me the story. Owner had loaned the saw out to a friend that was using it at the deer camp.   I told him how his mix looked and smelled. He dont know what mix other guy was using as it wasnt his.  He did say the friend wont be getting his saw anymore.
He dont know what dealer his friend took the saw to. But said he thought it was a small amish or mennonite type shop.

REDNECK Saw Repair Getter Done

Offline leec

  • 6 cube
  • ****
  • Posts: 262
  • Karma: 13
  • Location: Huntsville, Ontario
Re: Poulan 3314
« Reply #13 on: November 30, 2015, 11:00:58 am »
Does anyone know offhand what the initial carb settings are on these Stratos Poulans.  I'm out 2 1/2 on low speed and it still seems weak in the cut.

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 327
  • Karma: 28
Re: Poulan 3314
« Reply #14 on: November 30, 2015, 06:11:19 pm »
 2 and a half is pretty normal but it may need more

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20431
  • Karma: 446
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3314
« Reply #15 on: April 20, 2017, 04:18:56 pm »
 Checked the strato 3314 with same carb set up as 4218 it appears. Carb good to go but the oiler not working. Another easy fix.

 If I had known 3314 had a good carb I would have tried it on the 4218 with carb with issues. Oh well new carb already on its way.

Seems like another low hour saw

REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20431
  • Karma: 446
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3314
« Reply #16 on: May 22, 2017, 04:41:47 pm »
Oiler working great with the new replacement.  Only thing carb started acting funny in test cuts.  Pulled the cover and the black plastic piece for the air inlet cr acked and fell off. LOL
Good thing I bought that new carb for the 4218 that tuned out to be scored.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20431
  • Karma: 446
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3314
« Reply #17 on: May 24, 2017, 12:35:14 pm »
Shown the black plastic piece where it crac ked and fell off with the spring return.

REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20431
  • Karma: 446
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3314
« Reply #18 on: June 24, 2017, 01:40:41 pm »
I put the used half with plastic piece off the other saw.  Carb started acting like it needed kit. So I pulled the new carb off the scored one and installed new lines. Good to go.

So this one has new carb, new lines and new oiler.  More in it then I can sell for local.   :P 
Oh well make a good loaner if it dont sell for 40-50 local.
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
Poulan 415

Started by Cut4fun « 1 2 ... 9 10 » Poulan

94 Replies
2989 Views
Last post December 13, 2018, 04:15:16 pm
by Cut4fun .
Poulan 425

Started by Cut4fun « 1 2 » Poulan

15 Replies
993 Views
Last post March 18, 2014, 02:19:35 pm
by Cut4fun .
17 Replies
694 Views
Last post May 24, 2017, 06:52:22 pm
by 3000 FPS
Poulan 445

Started by 3000 FPS « 1 2 ... 15 16 » Poulan

151 Replies
3946 Views
Last post December 13, 2018, 12:09:14 pm
by Cut4fun .
7 Replies
473 Views
Last post April 13, 2014, 08:11:42 pm
by Cut4fun .
0 Replies
179 Views
Last post October 02, 2012, 11:36:18 am
by mweba
4 Replies
437 Views
Last post November 23, 2012, 12:28:15 am
by Andyshine77
23 Replies
826 Views
Last post November 02, 2015, 04:36:50 pm
by Cut4fun .
4 Replies
208 Views
Last post June 24, 2016, 12:31:36 pm
by MuddSaw
2 Replies
150 Views
Last post May 21, 2017, 08:59:45 pm
by Cut4fun .