Author Topic: Poulan 4000  (Read 4383 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21874
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4000
« Reply #30 on: March 17, 2014, 06:52:42 pm »
REDNECK Saw Repair Getter Done

Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4458
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: Poulan 4000
« Reply #31 on: March 17, 2014, 07:16:07 pm »
Tim is a geezer he still understands eh.   Right
PP 505, 475, 445.

Offline fossil

  • 6 cube
  • ****
  • Posts: 198
  • Karma: 59
  • Location: Brampton, Ontario
Re: Poulan 4000
« Reply #32 on: March 17, 2014, 07:25:53 pm »
Like..umm really? you guys are right. I'm "EH" to the bone.

When you guys were little did you ever say "I vote we do this"?

Tim

Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4458
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: Poulan 4000
« Reply #33 on: March 17, 2014, 07:32:00 pm »
Like..umm really? you guys are right. I'm "EH" to the bone.

When you guys were little did you ever say "I vote we do this"?



I cannot say I used it but I do remember others using it.   
PP 505, 475, 445.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan 4000
« Reply #34 on: March 18, 2014, 01:32:05 pm »
I hate to tell you this but apparently "eh" is seldom said now. I did hear someone say what we replaced it with but I can't remember. Too much back bacon and beer I guess.
I feel displaced now.

Somebody horked your word eh?

http://www.youtube.com/watch?v=7hfRActkm-U

-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan 4000
« Reply #35 on: March 18, 2014, 01:34:19 pm »
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline brokenbudget

  • Nitro Hotsaw
  • *******
  • Posts: 900
  • Karma: 67
  • Location: brockville ontario canada
Re: Poulan 4000
« Reply #36 on: March 18, 2014, 05:17:35 pm »
well, the flu sucks ;)
haven't had a chance to get a good look. but found this while poking around  :-[

the crack goes almost all the way to the front in a straight line. it's also missing the rear left tab.
need to get the cylinder off and see if it's ok. haven't had the muffler off yet.
anybody know any good welders? ;D
when I grow up, i wanna be an adult.

Offline fossil

  • 6 cube
  • ****
  • Posts: 198
  • Karma: 59
  • Location: Brampton, Ontario
Re: Poulan 4000
« Reply #37 on: March 18, 2014, 07:50:48 pm »
I can't think that would affect anything.
Tim

Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4458
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: Poulan 4000
« Reply #38 on: March 18, 2014, 07:53:39 pm »
Does it look like it was dropped the on the cylinder without the cover being on.
PP 505, 475, 445.

Offline brokenbudget

  • Nitro Hotsaw
  • *******
  • Posts: 900
  • Karma: 67
  • Location: brockville ontario canada
Re: Poulan 4000
« Reply #39 on: March 19, 2014, 07:13:31 am »
I can't think that would affect anything.

the crack goes all the way to the front in a straight line. there's only about an 1/8-1/4" holding the fin on. I don't want it fully breaking off. that's the very top fin of the combustion chamber, and I want all the fins in place if I'm going to be making a bit more heat. this isn't something I want done right. ;)
when I grow up, i wanna be an adult.

 

Related Topics

  Subject / Started by Replies Last post
1 Replies
386 Views
Last post November 27, 2011, 02:52:55 am
by Roanoker494
1 Replies
249 Views
Last post September 11, 2012, 10:24:23 am
by Cut4fun
4000 rpm's

Started by redunshee « 1 2 » Poulan

19 Replies
579 Views
Last post February 03, 2014, 11:46:52 pm
by 3000 FPS
19 Replies
1411 Views
Last post May 22, 2019, 10:19:04 am
by Cut4fun .
6 Replies
305 Views
Last post July 28, 2019, 12:23:26 pm
by countryhog
0 Replies
83 Views
Last post December 22, 2014, 01:22:11 pm
by Cut4fun .
3 Replies
252 Views
Last post February 21, 2017, 07:52:38 am
by mowertech
3 Replies
114 Views
Last post July 17, 2017, 04:40:15 pm
by dcook22
19 Replies
270 Views
Last post January 27, 2020, 08:20:42 am
by Cut4fun
0 Replies
53 Views
Last post May 01, 2020, 06:52:38 pm
by Cut4fun .