Author Topic: Poulan 4000  (Read 4338 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21640
  • Karma: 506
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Ebay find piston and cylinder
« Reply #150 on: May 17, 2019, 06:19:43 pm »
Sounds like one.

Going to move it to the 4000 thread where the specs are there for you to look at too.

3700 was also thin ring. So just check your bore specs compared to what is posted in threads here.

Pic of p+c set ?    Good price too 45.       I just sold whole 4000 for 125 and ship.

REDNECK Saw Repair Getter Done
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21640
  • Karma: 506
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4000
« Reply #151 on: July 10, 2019, 09:52:04 am »
Guys looking for those poulan 4000 395 pulleys dont pay those ebay gouging prices listed. I know a dealer that still has some in stock.
I am asking him if he wants me to buy the 2 or just send folks to him. If I have to buy them I will sell for my total cost plus the shipping for the guys in need of these.

REDNECK Saw Repair Getter Done
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21640
  • Karma: 506
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4000
« Reply #152 on: July 19, 2019, 03:32:16 pm »
Both NOS pulleys for 4000 395 and 3 NOS thin rings for same saws bought. Will set on shelf for folks needs.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21640
  • Karma: 506
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4000
« Reply #153 on: July 20, 2019, 12:36:07 pm »
Brand new never installed NOS poulan pro 395. Plus the poulan 4000 pulley which appears it may have been used at one time seeing the pawl drag.  Can see the stress crack they get in them even from just setting on shelf.

Still tight.



REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21640
  • Karma: 506
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4000
« Reply #154 on: July 26, 2019, 04:33:46 pm »
Pulleys and thin rings in hand.  1 NOS pulley and 1 used IMO.

The rings come in the sleeve and sold to me as NOS. But would like to make sure. I never measured the last NOS 4000 PP395 ring sets.
Like to know the width of ring.  Anyone have a NOS one to measure please?

Like I did with the 2100 thin rings =  New 2.07mm and used set 1.82mm and 1.86mm.

I know the thickness is .55mm
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21640
  • Karma: 506
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4000
« Reply #155 on: July 27, 2019, 07:52:09 am »
Todd said new were .60 mm thick,  2.06 mm width.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21640
  • Karma: 506
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4000
« Reply #156 on: July 28, 2019, 07:52:28 am »
Todd said new were  2.06 mm width.

They check out with my cheap calibers. 03-06
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21640
  • Karma: 506
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4000
« Reply #157 on: July 28, 2019, 10:03:27 am »
Just been paying attention to this lately. Seems most of the 4000 395 pulleys have that seam that opens a bit.
One in a used recoil that is FS right now I seen.

I checked the 2 I got in and both very tight and ready to use.   I had $9 in shipping for both. Split that between the 2.  One is NOS and 1 light wear used IMO. 


I'll get pics of the pulleys and poulan 4000 395 thin rings in a bit.




REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21640
  • Karma: 506
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4000
« Reply #158 on: July 28, 2019, 12:57:33 pm »
Poulan 4000 PP395 parts NOS and used. I just went through the parts I bought to help others keep this series of saws going.

The 4000 PP395 pulleys IMO is 1 nos and 1 used as I can see where the pawls turned on it. Both have that normal stress gap at the seam in the plastic area. But checked both over and both super tight and ready to go.

The 3 4000 PP395 thin rings I got in are 1 nos and 2 used set. NOS width is 2.06 and the 2 used measure 2.03 so not wore much at all.

These might fit the PP385 too, but never had one to check.

REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21640
  • Karma: 506
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 4000
« Reply #159 on: July 28, 2019, 04:45:14 pm »
Poulan 4000 PP395 parts NOS and used. I just went through the parts I bought to help others keep this series of saws going.

The 4000 PP395 pulleys IMO is 1 nos and 1 used as I can see where the pawls turned on it. Both have that normal stress gap at the seam in the plastic area. But checked both over and both super tight and ready to go.

The 3 4000 PP395 thin rings I got in are 1 nos and 2 used set. NOS width is 2.06 and the 2 used measure 2.03 so not wore much at all.

These might fit the PP385 too, but never had one to check.



@countryhog   Here is the info on the 3 rings. 
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
1 Replies
374 Views
Last post November 27, 2011, 02:52:55 am
by Roanoker494
1 Replies
245 Views
Last post September 11, 2012, 10:24:23 am
by Cut4fun
4000 rpm's

Started by redunshee « 1 2 » Poulan

19 Replies
578 Views
Last post February 03, 2014, 11:46:52 pm
by 3000 FPS
19 Replies
1376 Views
Last post May 22, 2019, 10:19:04 am
by Cut4fun .
6 Replies
244 Views
Last post July 28, 2019, 12:23:26 pm
by countryhog
0 Replies
81 Views
Last post December 22, 2014, 01:22:11 pm
by Cut4fun .
7 Replies
557 Views
Last post December 19, 2015, 05:19:42 pm
by leec
3 Replies
233 Views
Last post February 21, 2017, 07:52:38 am
by mowertech
3 Replies
113 Views
Last post July 17, 2017, 04:40:15 pm
by dcook22
19 Replies
243 Views
Last post January 27, 2020, 08:20:42 am
by Cut4fun