Author Topic: Poulan micro Super xxv Deluxe  (Read 1157 times)

0 Members and 0 Guests are viewing this topic.

Offline wcorey

  • 3 cube
  • *
  • Posts: 7
  • Karma: 4
Re: Poulan micro Super xxv Deluxe
« Reply #20 on: October 02, 2015, 10:00:20 am »

Quote
Since it's a Super...........it should be 38cc (same as a 2300).  May 'just' be 33cc however.  Bore measurement would tell the tale.

The basic 'popsicle stick' bore measurement on a couple of mine was ~1.43", same as the 2.0's...

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2108
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan micro Super xxv Deluxe
« Reply #21 on: October 02, 2015, 03:22:52 pm »
I have a 25da I think that's the number . It loks similar to the pic above on 1st page. Bought off a guy, it sat in his barn for god knows how long I put fresh gas in it and wammo. It ran, but like chit I think it has a air leak somewhere.

If it's a 25DA (and not a Micro 25DA) then it is a totally different saw than what we are talking about here.  Same mfg.  Somewhat similar look.  Almost no parts interchange though.  Part of the XXV series rather than the Micro series.  The XXV series are my favorite top handle saws.  Second for me (and the only other top handles that I like) are the Micro series.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.
Informative Informative x 1 View List

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2108
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan micro Super xxv Deluxe
« Reply #22 on: October 02, 2015, 03:25:07 pm »

Quote
Since it's a Super...........it should be 38cc (same as a 2300).  May 'just' be 33cc however.  Bore measurement would tell the tale.

The basic 'popsicle stick' bore measurement on a couple of mine was ~1.43", same as the 2.0's...

I'll measure it when it gets here.  Doesn't really matter to me either way though.  I have a Craftsman 2.3AV branded 2300AV for my 38cc Micro fix.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline old guy

  • 4 cube
  • **
  • Posts: 49
  • Karma: 12
Re: Poulan micro Super xxv Deluxe
« Reply #23 on: October 02, 2015, 06:26:35 pm »
last week I needed to measure a piston and while I i was bringing the piston down in the exhaust port I thought why don't   I just leave it stick up in the port a bit  then butt the long end of my caliper against the piston and push the caliper open till the pin hits the back side of the cyl. and read the dial, worked perfectly.

     John

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 149
  • Location: Hayesville, NC
Re: Poulan micro Super xxv Deluxe
« Reply #24 on: October 02, 2015, 11:37:58 pm »
Thanks!!!  Hadn't thought of that.
Shep

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21780
  • Karma: 519
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan micro Super xxv Deluxe
« Reply #25 on: October 03, 2015, 08:20:44 am »
If you blow this pic up bigger it says at bottom MICRO S25D 33CCM   wondering if 33CCM is 33cc Motor






REDNECK Saw Repair Getter Done

Offline stubnail67

  • 6 cube
  • ****
  • Posts: 178
  • Karma: 23
Re: Poulan micro Super xxv Deluxe
« Reply #26 on: October 04, 2015, 04:37:41 pm »
thats what i think

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2108
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan micro Super xxv Deluxe
« Reply #27 on: October 06, 2015, 03:56:52 pm »
Probably is...
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline wcorey

  • 3 cube
  • *
  • Posts: 7
  • Karma: 4
Re: Poulan micro Super xxv Deluxe
« Reply #28 on: October 08, 2015, 02:24:37 pm »
The pic of the guy heading out to cut wood with his cardboard box case is pretty funny. It's really thin, cheesy cardboard, you'd have to be really careful with it to get through the first outing, lol.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21780
  • Karma: 519
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan micro Super xxv Deluxe
« Reply #29 on: October 08, 2015, 02:27:58 pm »
Sweet pic.  You own the box?
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
4 Replies
973 Views
Last post April 02, 2012, 09:31:29 am
by 2spud
Poulan S25DA super 25

Started by Cut4fun « 1 2 ... 7 8 » Poulan

76 Replies
6082 Views
Last post December 23, 2015, 03:36:20 pm
by Eccentric
6 Replies
495 Views
Last post October 31, 2014, 02:59:37 pm
by Cut4fun .
7 Replies
881 Views
Last post December 04, 2013, 07:35:40 am
by doreadeal
Poulan Micro

Started by fossil « 1 2 » Poulan

14 Replies
455 Views
Last post May 08, 2020, 06:40:50 am
by Cut4fun .
Poulan micro XXV

Started by countryhog « 1 2 » Poulan

10 Replies
510 Views
Last post August 01, 2014, 09:45:30 pm
by Cut4fun .
16 Replies
1429 Views
Last post January 07, 2020, 07:57:44 am
by Super360
6 Replies
447 Views
Last post November 16, 2016, 01:09:22 pm
by Cut4fun .
8 Replies
272 Views
Last post January 14, 2019, 10:03:10 am
by trappermike
3 Replies
50 Views
Last post April 06, 2020, 07:47:38 am
by Cut4fun .