Author Topic: poulan predator 335  (Read 727 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: poulan predator 335
« Reply #10 on: November 07, 2014, 11:30:35 pm »
That would be interesting.   I never even thought of trying it.

Should be same set up in the predator 335 you have.

Except in a nice small tight package.   

I'm lost.

Its the same thing. Not understanding? 

2700 3.0 are all same size as the pred 335 etc powerhead wise. pred 335 has 3450 330 piston in the 335 cylinder. So same size still.  So no big changes. Heck factory done it, so no big deal IMO me wanting to throw a 3450 p in 335 c on on same size saw JMO.  ???
REDNECK Saw Repair Getter Done

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4468
  • Karma: 274
  • Location: Carpenter, Wyoming
Re: poulan predator 335
« Reply #11 on: November 07, 2014, 11:57:37 pm »
I was thinking 3450 cylinder and a 3450 size saw compared to a 335.   The 335 because of the air filter and cylinder cover design is smaller.   My misunderstanding. 
PP 505, 475, 445.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: poulan predator 335
« Reply #12 on: November 08, 2014, 12:02:50 am »
I thought we had switched tracks somewhere. Thats why I was asking.

 I am just using the extra 3450 piston out of the 3450 when I put the 60cc 3750 topend on 3450.  Then make one of the 46cc-49cc a 54cc predator type motor using 3450 p and 335 c.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: poulan predator 335
« Reply #13 on: November 08, 2014, 12:05:36 am »
If I was going to try the other I would put the 60cc on one. But with the 3500 365 around. I just dont see the use of doing that on a 2700-3300 saws.
 I still think all it would take is slotting and maybe crankcase open some for p skirt clearance.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: poulan predator 335
« Reply #14 on: July 16, 2015, 02:12:39 pm »
Just putting the poulan predator 335 stuff in this thread.  Hoggwood found one for sale up in Canada too. Will post pics. he said over by Tim aka fossil. ;)

I got the 335 Predator back together and took it for a quick check.   Saw runs good and I think I will stay with the 3/8, 16", .050 bar and chain on it.    I did the usual muffler mod, dropped the cylinder, advanced the timing, widened the intake and exhaust.    I put a new ring in it and cleaned up all the carbon from the piston and cylinder.    After running it and letting it cool down I got a 200 psi out of it so once again I am very pleased about that.   I like building these to add torque not neccessarily RPM.    Since cut4fun put up the before pictures I will provide the after pictures.



Rogers






The one hoggwood found and FS.



REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: poulan predator 335
« Reply #15 on: July 16, 2015, 02:21:12 pm »
Thread I mentioned @Hoggwood 

I updated with your find too. ;)
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: poulan predator 335
« Reply #16 on: July 17, 2015, 03:25:35 pm »
That's a very sharp looking variant of this series.  I like it a lot (OK I'm partial to red/black saws, especially when they're Poulans). 8)



Man my bench was a mess when I took that.  Need to take some fresh pics of the saws so I can stop using the messy bench pics.....
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Hoggwood

  • 4 cube
  • **
  • Posts: 64
  • Karma: 17
Re: poulan predator 335
« Reply #17 on: July 18, 2015, 02:11:55 pm »
Yes...sweet looking machine.  I sent you the particulars Kevin.

Cory

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4468
  • Karma: 274
  • Location: Carpenter, Wyoming
Re: poulan predator 335
« Reply #18 on: July 18, 2015, 11:37:46 pm »
That is pretty cool Hoggwood.   I have not seen many of the predators around.   Nice find.
PP 505, 475, 445.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4468
  • Karma: 274
  • Location: Carpenter, Wyoming
Re: poulan predator 335
« Reply #19 on: July 18, 2015, 11:51:44 pm »
Hey Aaron I think the red and black is good looking on a saw also.
PP 505, 475, 445.

 

Related Topics

  Subject / Started by Replies Last post
Poulan 425

Started by Cut4fun « 1 2 » Poulan

15 Replies
1092 Views
Last post March 18, 2014, 02:19:35 pm
by Cut4fun .
17 Replies
769 Views
Last post May 24, 2017, 06:52:22 pm
by 3000 FPS
Poulan 445

Started by 3000 FPS « 1 2 ... 18 19 » Poulan

181 Replies
4584 Views
Last post August 01, 2020, 08:05:18 am
by Cut4fun
7 Replies
521 Views
Last post April 13, 2014, 08:11:42 pm
by Cut4fun .
0 Replies
192 Views
Last post October 02, 2012, 11:36:18 am
by mweba
Poulan 395

Started by 3000 FPS « 1 2 3 » Poulan

23 Replies
981 Views
Last post January 05, 2013, 09:09:29 pm
by 3000 FPS
4 Replies
549 Views
Last post November 23, 2012, 12:28:15 am
by Andyshine77
23 Replies
1228 Views
Last post November 02, 2015, 04:36:50 pm
by Cut4fun .
Poulan 335

Started by 3000 FPS « 1 2 3 4 5 » Poulan

46 Replies
1324 Views
Last post February 14, 2020, 09:23:59 am
by Cut4fun .
Poulan 380

Started by Cut4fun . « 1 2 ... 7 8 » Poulan

78 Replies
2113 Views
Last post March 01, 2020, 08:06:34 am
by Cut4fun .