Author Topic: Poulan pro 236  (Read 1500 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21042
  • Karma: 468
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan pro 236
« Reply #40 on: October 11, 2015, 02:06:34 pm »
@stubnail67  I can do this while watching football.

Here is new stuff.

Poulan micro clutch and drums.


Clutch drum 530069166  $14
Clutch Bearing 530032079 $5
Washer kit 530069197 $7
Clutch NLA

REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21042
  • Karma: 468
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
REDNECK Saw Repair Getter Done

Offline stubnail67

  • 6 cube
  • ****
  • Posts: 172
  • Karma: 22
Re: Poulan pro 236
« Reply #42 on: October 12, 2015, 04:19:03 pm »

Offline stubnail67

  • 6 cube
  • ****
  • Posts: 172
  • Karma: 22
Re: Poulan pro 236
« Reply #43 on: October 12, 2015, 04:21:58 pm »
you would think there would be a replacement out there that would work.....im gonna order the spurs and email mowers for you see if they have any knowledge....if not may have to buy from the bay thanks for looking....swear i have 2 or 3 of those old style clutches in a tin some where in some bin
 

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21042
  • Karma: 468
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan pro 236
« Reply #44 on: October 12, 2015, 05:02:08 pm »
I still need to dig for clutches etc.  I know there was a older and newer but know of no cross overs.

I know I have 2 complete sets on 2 runners I dont use. Would sell the runners for the cost of the sets.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21042
  • Karma: 468
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan pro 236
« Reply #45 on: October 15, 2015, 02:24:32 pm »
you would think there would be a replacement out there that would work.....im gonna order the spurs and email mowers for you see if they have any knowledge....if not may have to buy from the bay thanks for looking....swear i have 2 or 3 of those old style clutches in a tin some where in some bin
 

I looked yesterday. Extras not much. 1 spur drum with half wear but usable IMO. I wouldnt waste time on it shipping. Also 1 bearing. 1 old style clutch with weird wear on 1 shoe, again wouldnt bother with it.
 
The 2 runners have the nicer complete set ups I have.  Both run but 1 needs carb rebuilt. I just switch the good carb between them when tested.   Trade both saws for?  or sell the 2 complete set ups or trade for?
REDNECK Saw Repair Getter Done

Offline Orville

  • pruner
  • *
  • Posts: 1
  • Karma: 0
  • Location: Philippines
    • Cordless Chainsaw Finder
Re: Poulan pro 236
« Reply #46 on: December 04, 2015, 05:13:31 am »
A lot of suggestions out there. I hope the problem is solved.

Offline Drew_Uth

  • 4 cube
  • **
  • Posts: 38
  • Karma: 3
Re: Poulan pro 236
« Reply #47 on: December 04, 2015, 09:51:33 am »
I'm curious about all the ring mixing and matching you guys do, and the plated/unplated cylinders.  Working on bikes, rings for plated cylinders are very different from rings for bikes with plated cylinders, and mixing them up ruins the bore.  With all the Poulan/Craftsman variants that may share bore sizes but not bore type, are you ever concerned about the wrong rings?  Or have you found it to be a non-issue?

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21042
  • Karma: 468
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan pro 236
« Reply #48 on: December 04, 2015, 10:59:11 am »
I'm curious about all the ring mixing and matching you guys do, and the plated/unplated cylinders.  Working on bikes, rings for plated cylinders are very different from rings for bikes with plated cylinders, and mixing them up ruins the bore.  With all the Poulan/Craftsman variants that may share bore sizes but not bore type, are you ever concerned about the wrong rings?  Or have you found it to be a non-issue?

We dont mix unplated and plated they are only done in sets when swapped.
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
Poulan 475

Started by Cut4fun « 1 2 ... 35 36 » Poulan

351 Replies
8713 Views
Last post October 25, 2018, 02:04:51 pm
by Cut4fun .
Poulan 415

Started by Cut4fun « 1 2 ... 9 10 » Poulan

99 Replies
3150 Views
Last post January 04, 2019, 10:21:27 am
by Cut4fun .
Poulan 220

Started by Cut4fun . « 1 2 » Poulan

17 Replies
762 Views
Last post June 17, 2017, 12:25:32 pm
by Cut4fun .
Poulan 365

Started by Cut4fun « 1 2 ... 16 17 » Poulan

169 Replies
4805 Views
Last post January 31, 2018, 07:59:31 pm
by stubnail67
Poulan 1800

Started by Cut4fun . « 1 2 » Poulan

12 Replies
1131 Views
Last post December 23, 2013, 06:06:19 pm
by bustedknuckles
221 Replies
5683 Views
Last post June 21, 2018, 08:30:48 am
by Cut4fun .
4 Replies
449 Views
Last post November 23, 2012, 12:28:15 am
by Andyshine77
23 Replies
866 Views
Last post November 02, 2015, 04:36:50 pm
by Cut4fun .
2 Replies
156 Views
Last post May 21, 2017, 08:59:45 pm
by Cut4fun .
8 Replies
146 Views
Last post December 31, 2018, 09:04:53 am
by Cut4fun .