« previous next »
Pages: 1 ... 10 11 12 13 14 [15] 16 17 18 19 20 ... 45   Go Down

Author Topic: Poulan 330 3450  (Read 20500 times)

0 Members and 59 Guests are viewing this topic.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

    • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Poulan PRO 330
« Reply #140 on: January 11, 2014, 05:20:32 pm »
I believe the worm gear is made from steel so that would not be it.  The pump itself I think has a nylon gear on it and that would strip out first.   If it is real cold out I would try thinning the oil out some.   I do that on all my saws in cold weather just so the oil can flow better.   Take the bar and chain off start it up with the clutch cover off and see if any oil is coming out of the side.   
Logged
PP 505, 475, 445.

Offline magnumfloyd

  • 4 cube
  • **
  • Posts: 63
  • Karma: 10
  • Location: Millville, NJ

    • Total Badges: 19
    Badges: (View All)
    Third year Anniversary Second year Anniversary 50 Posts Level 4 One year Anniversary Karma Good
Re: Poulan PRO 330
« Reply #141 on: January 18, 2014, 12:29:33 am »
It was definitely the pump gear anyone no where I can find one in stock . Gear part number is 530027129 and the pin I needed to remove is part number 530015752
Logged

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

    • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Poulan PRO 330
« Reply #142 on: January 18, 2014, 12:35:01 am »
The part number you listed for a spur gear is listed at Jack's for 89 cents.
http://www.jackssmallengines.com/Parts-Lookup/530027129/2151645/PL

The other part number is listed at Jacks also.
http://www.jackssmallengines.com/Parts-Lookup/530015752/2149259/PL
Logged
PP 505, 475, 445.

Offline magnumfloyd

  • 4 cube
  • **
  • Posts: 63
  • Karma: 10
  • Location: Millville, NJ

    • Total Badges: 19
    Badges: (View All)
    Third year Anniversary Second year Anniversary 50 Posts Level 4 One year Anniversary Karma Good
Re: Poulan PRO 330
« Reply #143 on: January 18, 2014, 10:18:42 am »
Thanks but I hate paying 7.95 shipping on 2 dollars worth of parts.
Logged

Offline magnumfloyd

  • 4 cube
  • **
  • Posts: 63
  • Karma: 10
  • Location: Millville, NJ

    • Total Badges: 19
    Badges: (View All)
    Third year Anniversary Second year Anniversary 50 Posts Level 4 One year Anniversary Karma Good
Re: Poulan PRO 330
« Reply #144 on: February 04, 2014, 08:43:16 pm »
Okay so I added a 1" slit to the front cover of the muffler and removed the crossover tube the baffle has two square holes should I add two addition 3/8 holes on the other side of the diffuser.
Logged

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

    • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Poulan PRO 330
« Reply #145 on: February 04, 2014, 08:47:51 pm »
If it were my saw yes.
Logged
PP 505, 475, 445.

Offline magnumfloyd

  • 4 cube
  • **
  • Posts: 63
  • Karma: 10
  • Location: Millville, NJ

    • Total Badges: 19
    Badges: (View All)
    Third year Anniversary Second year Anniversary 50 Posts Level 4 One year Anniversary Karma Good
Re: Poulan PRO 330
« Reply #146 on: February 04, 2014, 08:51:18 pm »
Sounds good I have an new extra muffler from my new chain brake so ill try it.
Logged

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

    • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Poulan PRO 330
« Reply #147 on: February 04, 2014, 09:10:34 pm »
When I muffler mod those baffles I take a cut off saw and cut half of it away on both sides.    So you will be fine with the holes.
Logged
PP 505, 475, 445.

Offline magnumfloyd

  • 4 cube
  • **
  • Posts: 63
  • Karma: 10
  • Location: Millville, NJ

    • Total Badges: 19
    Badges: (View All)
    Third year Anniversary Second year Anniversary 50 Posts Level 4 One year Anniversary Karma Good
Re: Poulan PRO 330
« Reply #148 on: February 04, 2014, 11:06:46 pm »
The hole in my hand isn't helping anything sitting at the er I drilled through the one side and came clear threw the fact tory hole and into my palm :'(
Logged

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

    • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Poulan PRO 330
« Reply #149 on: February 04, 2014, 11:25:09 pm »
Well what do you know.   I have one of those too, except mine is from a cut off wheel.
Logged
PP 505, 475, 445.
Pages: 1 ... 10 11 12 13 14 [15] 16 17 18 19 20 ... 45   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
3 Replies
1059 Views 		Last post February 03, 2013, 06:33:10 pm
by 660magnum
Poulan 3450 60cc

Started by Cut4fun . « 1 2 ... 6 7 » Poulan

66 Replies
4143 Views 		Last post February 08, 2018, 07:01:11 pm
by 3000 FPS
16 Replies
2796 Views 		Last post April 11, 2014, 07:03:51 am
by Tractorsaw1
Poulan 3450 Carb issues

Started by rockfishon « 1 2 ... 7 8 » Poulan

77 Replies
3223 Views 		Last post August 27, 2015, 07:55:47 pm
by Eccentric
5 Replies
909 Views 		Last post October 23, 2014, 06:53:51 pm
by Cut4fun .
120 Replies
5490 Views 		Last post October 07, 2023, 08:09:15 am
by Cut4fun
16 Replies
979 Views 		Last post May 17, 2015, 10:00:49 am
by Cut4fun
2 Replies
606 Views 		Last post March 20, 2015, 10:16:41 pm
by 3000 FPS
8 Replies
801 Views 		Last post June 05, 2015, 09:52:30 am
by Cut4fun .
2 Replies
447 Views 		Last post February 28, 2018, 01:25:07 pm
by Cut4fun .