Author Topic: Poulan 330 3450  (Read 12241 times)

0 Members and 0 Guests are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2112
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northwestern Wyoming
Re: Poulan 330 3450
« Reply #360 on: July 10, 2017, 02:54:30 pm »
Wow.  She ate something....

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22586
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 330 3450
« Reply #361 on: July 10, 2017, 07:22:56 pm »
Wow.  She ate something....

Long time. Hope all is well with you and family.

Ate welding spatter. Because some dumb hind end welded the cracks around front of muffler bolt with it on the saw. 

3 months to go, paper work signed back in June. ;)
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22586
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 330 3450
« Reply #362 on: August 26, 2017, 09:08:07 am »
Finished up the poulan 3450 type 3 60cc yesterday. Not done though. Wouldnt pop. 

Before build. Had looked through exhaust with muffler etc all off. Looked like new still. Looked through plug hole all the same.  So had never pulled the cylinder.

Check spark etc all good with spark analyzer. Just by pull test psi all felt good. Checked psi with tester not good. 90psi.
First thought stuck ring. Yep on back side by ring pin one side was stuck for about 1/2-3/4 inch.

So pulled down.
Waiting on base gasket for this one that is on order. Due to I ran out on 380 when I used the dirko ht for its base gasket.

REDNECK Saw Repair Getter Done
Like Like x 1 View List

Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4549
  • Karma: 293
  • Location: Carpenter, Wyoming
Re: Poulan 330 3450
« Reply #363 on: August 26, 2017, 04:51:18 pm »
Yep 90 psi is pretty marginal.
PP 505, 475, 445.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22586
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 330 3450
« Reply #364 on: August 26, 2017, 09:15:17 pm »
Yep 90 psi is pretty marginal.

Whats weird didnt feel or pop like 90psi to me.

Got the stuck end broke loose today using with PB blaster and very small round chisel and small hammer.

So clean the crud out of the groove. New ring and base gasket. Then should be good.
REDNECK Saw Repair Getter Done
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22586
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 330 3450
« Reply #365 on: August 28, 2017, 03:24:02 pm »
Put crosshatch with ball hone and new ring after cleaning up the gunky groove.  Just waiting on my gasket kit. Hoping today delivery.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22586
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 330 3450
« Reply #366 on: August 28, 2017, 10:47:50 pm »
She lives. Gasket came in this evening.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22586
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 330 3450
« Reply #367 on: August 29, 2017, 03:10:28 pm »
Poulan 3450 type 3  test and tuned today. 

pics

REDNECK Saw Repair Getter Done
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22586
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 330 3450
« Reply #368 on: September 19, 2017, 06:23:28 pm »
Fired off another PP330 today from the saws I been stocking back. Bench 2 has been cleared.  Which suks because I was stocking up for winter builds.

New fuel lline, impulse line and trying a new rc clamp for impulse lines.  2 new rubber av's and tensioner.

What I started with



REDNECK Saw Repair Getter Done

Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4549
  • Karma: 293
  • Location: Carpenter, Wyoming
Re: Poulan 330 3450
« Reply #369 on: September 19, 2017, 06:42:49 pm »
So where is the after pic.
PP 505, 475, 445.

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
454 Views
Last post February 03, 2013, 06:33:10 pm
by 660magnum
Poulan 3450 60cc

Started by Cut4fun . « 1 2 ... 6 7 » Poulan

66 Replies
2007 Views
Last post February 08, 2018, 07:01:11 pm
by 3000 FPS
16 Replies
1249 Views
Last post April 11, 2014, 07:03:51 am
by Tractorsaw1
Poulan 3450 Carb issues

Started by rockfishon « 1 2 ... 7 8 » Poulan

77 Replies
1296 Views
Last post August 27, 2015, 07:55:47 pm
by Eccentric
5 Replies
404 Views
Last post October 23, 2014, 06:53:51 pm
by Cut4fun .
111 Replies
2008 Views
Last post September 27, 2015, 09:41:29 pm
by 3000 FPS
16 Replies
311 Views
Last post May 17, 2015, 10:00:49 am
by Cut4fun
2 Replies
209 Views
Last post March 20, 2015, 10:16:41 pm
by 3000 FPS
8 Replies
301 Views
Last post June 05, 2015, 09:52:30 am
by Cut4fun .
2 Replies
160 Views
Last post February 28, 2018, 01:25:07 pm
by Cut4fun .