Author Topic: Poulan 415  (Read 3700 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 415
« Reply #40 on: February 01, 2016, 12:40:14 pm »
please give me pointers to fine tune it. It will run and idle for about two minutes by itself. Starts right back up. Does the impulse line need check valves etc.

no checks.

did you say you put a new carb rebuild kit in it?
I did rebuild the carb but may need to go back in and set the metering height to flush with top of metering deck. I set it to flush with carburetor top

Sent from my LG-D800 using Tapatalk



I dont remember the right setting off hand. Do you?
You need me to check my book or a carb I have off?
REDNECK Saw Repair Getter Done

Offline acornhill

  • 3 cube
  • *
  • Posts: 23
  • Karma: 1
Re: Poulan 415
« Reply #41 on: February 29, 2016, 09:48:57 pm »
i finally went back in the 415 carburetor and reset the metering lever to flush with metering ceiling. I am now ready to run her again. I did the same thing to the PP525 i have and that saw is a beast now. It is amazing that moving the lever height such a small amount can make such a big difference.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 415
« Reply #42 on: June 05, 2016, 04:46:29 pm »
Here is the extra small dawg installed on my poulan 415. It is perfect for using the shorter bar IMO.

The extra small laid on top of the small one to compare them.



REDNECK Saw Repair Getter Done
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 415
« Reply #43 on: January 16, 2017, 07:47:45 pm »
While buying the NOS poulan parts today.

The dealer said he had a poulan 415 with the old style tank and air filter set up setting on the bench. Customers saw.

I was offered it today too. So Now I have another 415 coming in.  So it will be getting the updated tank and air filter set up like on the 505. ;)

REDNECK Saw Repair Getter Done

Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4460
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: Poulan 415
« Reply #44 on: January 16, 2017, 08:50:22 pm »
I know you like those saws.
PP 505, 475, 445.
Agree Agree x 1 View List

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4045
  • Karma: 159
  • OHIO REDNECK
Re: Poulan 415
« Reply #45 on: January 17, 2017, 01:06:59 pm »
Has the typical issues with this series when rode hard.  Jerked in the cuts, pushed down on and maybe a drop.

6 pics I was shown

REDNECK Saw Repair

Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4460
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: Poulan 415
« Reply #46 on: January 17, 2017, 07:59:41 pm »
Yep It sure has seen a little miss use.    But still I know you will make it into a good running work saw.   
PP 505, 475, 445.
Agree Agree x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 415
« Reply #47 on: January 18, 2017, 12:06:39 pm »
65cc top will get pulled in time after testing out. Just not sure which top I put back. Leaning toward a 445.

Was thinking of pulling the 505 off the wild thing for another 445. Butttttt now.


Still getting parts off the shelves and out of bins for the 475 a guy wants to build.  Need to split the 2 475 crankcases and pull the good crank for the better crankcase. Better crankcase has a big end rod bearing out. 

REDNECK Saw Repair Getter Done

Online Fishnuts2

  • 4 cube
  • **
  • Posts: 56
  • Karma: 15
Re: Poulan 415
« Reply #48 on: January 22, 2017, 08:53:50 am »
I just bought a 415 and am anxious to run one.  However, it needs a clutch cover.
Does anyone here have one that I could purchase?
Thanks!
Like Like x 1 View List

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4045
  • Karma: 159
  • OHIO REDNECK
Re: Poulan 415
« Reply #49 on: January 22, 2017, 10:15:43 am »
I just bought a 415 and am anxious to run one.  However, it needs a clutch cover.
Does anyone here have one that I could purchase?
Thanks!


I would have to check. I know I just set one aside for a whole 475 in parts I am setting out for a possible buyer out of US.

Also you can make one out of a husky 268 272 etc clutch cover.  I've done it before and it works.
REDNECK Saw Repair

 

Related Topics

  Subject / Started by Replies Last post
Poulan 365

Started by Cut4fun « 1 2 ... 16 17 » Poulan

169 Replies
4997 Views
Last post January 31, 2018, 07:59:31 pm
by stubnail67
Poulan 295 Porting

Started by Dh1984 « 1 2 » Poulan

11 Replies
1406 Views
Last post May 20, 2011, 08:55:11 am
by Dh1984
3 Replies
371 Views
Last post June 11, 2011, 05:25:29 pm
by Cut4fun
Poulan pro 236

Started by Cut4fun . « 1 2 3 4 5 » Poulan

48 Replies
1610 Views
Last post December 04, 2015, 10:59:11 am
by Cut4fun .
Poulan 1800

Started by Cut4fun . « 1 2 » Poulan

12 Replies
1182 Views
Last post December 23, 2013, 06:06:19 pm
by bustedknuckles
222 Replies
6600 Views
Last post June 29, 2020, 07:46:24 pm
by Cut4fun .
4 Replies
536 Views
Last post November 23, 2012, 12:28:15 am
by Andyshine77
23 Replies
1188 Views
Last post November 02, 2015, 04:36:50 pm
by Cut4fun .
2 Replies
214 Views
Last post May 21, 2017, 08:59:45 pm
by Cut4fun .
8 Replies
210 Views
Last post December 31, 2018, 09:04:53 am
by Cut4fun .