Author Topic: Poulan pro 5020 PR5020 Poulan 5020 4818  (Read 6622 times)

0 Members and 2 Guests are viewing this topic.

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: Poulan pro 5020
« Reply #30 on: February 28, 2013, 05:53:25 pm »
I see you must have used it. Hows it run?? unless it came with sawdust on it.. :)
Ron

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21891
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan pro 5020
« Reply #31 on: February 28, 2013, 05:59:27 pm »
OUT OF THE BOX NEW a homeowner sawer would get disgusted pretty quick IMO.  The saw carb was off the mark on L and I.

I checked factory settings and then put them back to see. L was 1.5 and H was 2 - 2.5 out (sorry cant remember H off hand).

It would start and not idle and shut off. Start and bog giving throttle. 

I kept adjusting the carb till I ended up with about 3 out on L and left 2-2.5 on H at about 12.8K. Turned the I idle up too.  Reminds me of the redmax carb and settings (which through me for a loop when I 1st got it), not like the 1 to 1.5 turns out we get used to.

Got to make some test cuts and I was   ;D   ear to ear.

Be warned make sure you have the splined carb tool $8-$14 and know how to tune a saw if buying NIB.

K095 mount







REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21891
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan pro 5020
« Reply #32 on: February 28, 2013, 06:00:37 pm »
I see you must have used it. Hows it run?? unless it came with sawdust on it.. :)

Just left a new post. 

Well worth the $200 usual price tag IMO. 
REDNECK Saw Repair Getter Done

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4461
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: Poulan pro 5020
« Reply #33 on: February 28, 2013, 06:52:24 pm »
PP 505, 475, 445.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21891
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan pro 5020
« Reply #34 on: February 28, 2013, 07:06:07 pm »
K095 mount.

Sorry about that.  I thought they came with a K041.   

fixed it.    ;D

No biggie for me being I had both on hand.

 Now if someone was buying a bar it might have mattered.
REDNECK Saw Repair Getter Done

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4461
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: Poulan pro 5020
« Reply #35 on: February 28, 2013, 07:45:35 pm »
You know I thought for sure the K041 oiled through the adjuster holes and the K095 small husky mount oiled through a oil hole.   I do not see a oil hole in the bar laying flat in the picture. 

Then I also thought the K041 used 70 DL and the Husky K095 used 72 DL.
PP 505, 475, 445.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4049
  • Karma: 159
  • OHIO REDNECK
Re: Poulan pro 5020
« Reply #36 on: February 28, 2013, 07:48:31 pm »
You know I thought for sure the K041 oiled through the adjuster holes and the K095 small husky mount oiled through a oil hole.   I do not see a oil hole in the bar laying flat in the picture. 

Then I also thought the K041 used 70 DL and the Husky K095 used 72 DL.

Look closer at the O in the bar laying down.
REDNECK Saw Repair

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4049
  • Karma: 159
  • OHIO REDNECK
Re: Poulan pro 5020
« Reply #37 on: February 28, 2013, 07:54:35 pm »
Tried to draw a line to oiler hole for you. Couldnt figure out how to change color though. Black line.  ???

K095 70DL bar with oregon vanguard 3/8 70dl chain.

REDNECK Saw Repair

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4461
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: Poulan pro 5020
« Reply #38 on: February 28, 2013, 07:57:13 pm »
I wonder if they started out using a K041 bar mount and then later switched to a K095.
PP 505, 475, 445.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4461
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: Poulan pro 5020
« Reply #39 on: February 28, 2013, 08:06:33 pm »
I thought I had read somewhere they used a K041 mount and I went back to the one Mark had done his reviews on and he is pretty convinced the one he got came with a K041 mount that oiled through the adjuster not a oil hole.     So I am just wondering if they changed it over to what you have now.
PP 505, 475, 445.

 

Related Topics

  Subject / Started by Replies Last post
Poulan 505

Started by man of stihl « 1 2 ... 40 41 » Poulan

406 Replies
8318 Views
Last post July 05, 2020, 08:47:06 am
by Cut4fun
4 Replies
540 Views
Last post November 23, 2012, 12:28:15 am
by Andyshine77
23 Replies
1192 Views
Last post November 02, 2015, 04:36:50 pm
by Cut4fun .
9 Replies
356 Views
Last post July 09, 2013, 04:07:30 pm
by moparman texas
3 Replies
269 Views
Last post March 09, 2013, 06:49:38 pm
by Cut4fun .
11 Replies
472 Views
Last post March 16, 2014, 04:12:43 pm
by Cut4fun .
1 Replies
136 Views
Last post May 14, 2015, 03:29:42 pm
by 660magnum
10 Replies
313 Views
Last post April 27, 2016, 02:22:24 pm
by deezlfan
2 Replies
217 Views
Last post May 21, 2017, 08:59:45 pm
by Cut4fun .
8 Replies
211 Views
Last post December 31, 2018, 09:04:53 am
by Cut4fun .