« previous next »
Pages: [1] 2 3 4 5 6 ... 39   Go Down

Author Topic: Poulan 505  (Read 7799 times)

0 Members and 0 Guests are viewing this topic.

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Poulan 505
« on: February 26, 2011, 07:35:44 am »
s\My Pictures\saw pics\saw pics 024.jpg
my pp 505 project
Logged
Ron

Share on Facebook Share on Twitter Share on Google+

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: poulan projects
« Reply #1 on: February 26, 2011, 07:37:28 am »
C:\Documents and Settings\Owner\My Documents\My Pictures\saw pics\saw pics 025
Logged
Ron

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: poulan projects
« Reply #2 on: February 26, 2011, 06:29:11 pm »
y Pictures\stuff\stuff 278.jpg
before muriatic acid
Logged
Ron

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: poulan projects
« Reply #3 on: February 26, 2011, 06:30:50 pm »
My Pictures\stuff\stuff 279.jpg
after muriatic acid :)
Logged
Ron

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 3810
  • Karma: 141
  • OHIO REDNECK
Re: poulan projects
« Reply #4 on: February 26, 2011, 06:41:58 pm »
Did you measure the bore? Is it the 505 82cc and did you find the right ring for replacement.
Logged
REDNECK Saw Repair

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: poulan projects
« Reply #5 on: February 26, 2011, 07:01:29 pm »
the bore measured 54mm and the ring should be in monday or tuesday. 8) the 475 is 52mm.correct?
Logged
Ron

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: poulan projects
« Reply #6 on: February 26, 2011, 07:23:27 pm »
My Pictures\saw pics\stuff.jpg
the piston cleaned up well also. i dont have a before pic :-[
Logged
Ron

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: Poulan 505 projects
« Reply #7 on: February 28, 2011, 06:42:33 pm »
i did a light port job on the cylinder tonight. both ports seemed real wide. about 2mm from piston witness lines so i left the sides alone. raised the roof in the exhaust a little. lowered the intake a little.cleaned out casting flaws in piston windows. replaced gasket with threebond 1194. put the cylinder back on. did a compression test got 150 psi. ;D ;D ;D.  i'll finish tomorrow i hope.
Logged
Ron

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1960
  • Karma: 169
Re: Poulan 505 projects
« Reply #8 on: February 28, 2011, 07:35:17 pm »
Do you have the rev-limited green coil in it?
Logged

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: Poulan 505 projects
« Reply #9 on: February 28, 2011, 08:39:20 pm »
Quote from: Gatekeeper on February 28, 2011, 07:35:17 pm
Do you have the rev-limited green coil in it?
well the coil is green! :'( finished putting it together. i couldn't stand it. i had to see how it runs. seems to run good. nice throttle response. idles ok too. ;D
Logged
Ron
Pages: [1] 2 3 4 5 6 ... 39   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
Poulan 365

Started by Cut4fun « 1 2 ... 16 17 » Poulan

169 Replies
4754 Views 		Last post January 31, 2018, 07:59:31 pm
by stubnail67
Poulan pro 236

Started by Cut4fun . « 1 2 3 4 5 » Poulan

48 Replies
1487 Views 		Last post December 04, 2015, 10:59:11 am
by Cut4fun .
Poulan 260

Started by Cut4fun « 1 2 3 » Poulan

22 Replies
1253 Views 		Last post September 19, 2016, 08:43:52 pm
by Chris-PA
Poulan s-25

Started by Al Smith « 1 2 3 4 5 » Poulan

40 Replies
2536 Views 		Last post February 07, 2014, 05:41:44 pm
by Eccentric
79 Replies
2643 Views 		Last post December 09, 2012, 02:51:01 pm
by Cut4fun .
1 Replies
352 Views 		Last post August 14, 2011, 04:40:12 pm
by Cut4fun .
221 Replies
5480 Views 		Last post June 21, 2018, 08:30:48 am
by Cut4fun .
4 Replies
437 Views 		Last post November 23, 2012, 12:28:15 am
by Andyshine77
23 Replies
826 Views 		Last post November 02, 2015, 04:36:50 pm
by Cut4fun .
2 Replies
150 Views 		Last post May 21, 2017, 08:59:45 pm
by Cut4fun .