Author Topic: Poulan 505  (Read 7927 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21119
  • Karma: 471
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 505 projects
« Reply #30 on: March 21, 2011, 03:33:24 pm »
Just thought this was cool a video of a new 505 with less then a tank through it so far.

mweba

http://www.youtube.com/watch?v=X2YhYwA6eU0
http://www.youtube.com/watch?v=qae22UrJPIk

REDNECK Saw Repair Getter Done

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 66
  • Information collector
  • Location: Troms, North Norway
Re: Poulan 505 projects
« Reply #31 on: March 23, 2011, 01:25:45 pm »
Niko, off hand as far as I can tell, the 415 and 475 never had the air injection while the 425,445 and 505 all did.

That is logic with the 415, but I have my doubts about the 475, as both the P7700 and the 2077 came both without and with it..... ???

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 66
  • Information collector
  • Location: Troms, North Norway
Re: Poulan 505 projects
« Reply #32 on: March 23, 2011, 01:33:04 pm »
Thce saw really is a Partner, and the original design was the P7700.

The "family" consisted of P7700, 710 and 660 -
Most (if not all) were made at the Husqvarna factory in Sweden, but there never was a Husky version...... ;)

So is the Partner 7700 710 660 a partner made saw or like the poulans a jonsered  saw relabeled?

The P7700 was the original design, but the saws were made at the Husky factory, at least from 1990 and on (most likely all the time, but I am lacking evidense of that).

Offline Modifiedmark

  • 5 cube
  • ***
  • Posts: 80
  • Karma: 2
Re: Poulan 505 projects
« Reply #33 on: March 23, 2011, 10:47:55 pm »
Niko, off hand as far as I can tell, the 415 and 475 never had the air injection while the 425,445 and 505 all did.

That is logic with the 415, but I have my doubts about the 475, as both the P7700 and the 2077 came both without and with it..... ???


Could be, but I have yet to see a 475 with it, but that don't mean anything really.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 3921
  • Karma: 143
  • OHIO REDNECK
Re: Poulan 505 projects
« Reply #34 on: March 26, 2011, 07:35:43 pm »
Niko, off hand as far as I can tell, the 415 and 475 never had the air injection while the 425,445 and 505 all did.
That is logic with the 415, but I have my doubts about the 475, as both the P7700 and the 2077 came both without and with it..... ???
Could be, but I have yet to see a 475 with it, but that don't mean anything really.

Made me look today 415 475 dont have air injection or de-comp on my 2.  The 505 has both.

REDNECK Saw Repair

Offline mweba

  • Piped Saw
  • *****
  • Posts: 390
  • Karma: 53
Re: Poulan 505 projects
« Reply #35 on: March 27, 2011, 10:50:23 pm »
Does your 505 have the "pre filter" at the carb adjust location?  Mine does not and seams never did.  This would make sense as the it would source air from the air injection.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 3921
  • Karma: 143
  • OHIO REDNECK
Re: Poulan 505 projects
« Reply #36 on: March 28, 2011, 08:58:26 pm »
I see no pre-filter on the 505 and  I dont see one on the IPL I use either.

Seems to be 2 different air filters, but everything I have is the fine mesh pleated vertically.
REDNECK Saw Repair

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 66
  • Information collector
  • Location: Troms, North Norway
Re: Poulan 505 projects
« Reply #37 on: March 30, 2011, 11:49:50 am »
The saws that have the fully developed "air injection" don't have the prefilter - it is one or the other, never both, in any IPL I have seen.

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 66
  • Information collector
  • Location: Troms, North Norway
Re: Poulan 505 projects
« Reply #38 on: March 30, 2011, 11:57:37 am »
Niko, off hand as far as I can tell, the 415 and 475 never had the air injection while the 425,445 and 505 all did.

That is logic with the 415, but I have my doubts about the 475, as both the P7700 and the 2077 came both without and with it..... ???


Could be, but I have yet to see a 475 with it, but that don't mean anything really.
I can't find a single 475 IPL that show it either.....



Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 3921
  • Karma: 143
  • OHIO REDNECK
Re: Poulan 505 projects
« Reply #39 on: May 01, 2011, 05:33:39 pm »
I knew there was something different about the 505 muffler when I first got it.

Today after comparing 505 475 415 mufflers I see the difference now. Anyone else have the muffler like on the 505? Maybe on a 2083 or 2083 II.

505




475




415





REDNECK Saw Repair

 

Related Topics

  Subject / Started by Replies Last post
Poulan 475

Started by Cut4fun « 1 2 ... 35 36 » Poulan

351 Replies
8727 Views
Last post October 25, 2018, 02:04:51 pm
by Cut4fun .
Poulan 260

Started by Cut4fun « 1 2 3 » Poulan

22 Replies
1265 Views
Last post September 19, 2016, 08:43:52 pm
by Chris-PA
Poulan s-25

Started by Al Smith « 1 2 3 4 5 » Poulan

40 Replies
2543 Views
Last post February 07, 2014, 05:41:44 pm
by Eccentric
79 Replies
2658 Views
Last post December 09, 2012, 02:51:01 pm
by Cut4fun .
1 Replies
356 Views
Last post August 14, 2011, 04:40:12 pm
by Cut4fun .
221 Replies
5737 Views
Last post June 21, 2018, 08:30:48 am
by Cut4fun .
4 Replies
453 Views
Last post November 23, 2012, 12:28:15 am
by Andyshine77
23 Replies
877 Views
Last post November 02, 2015, 04:36:50 pm
by Cut4fun .
2 Replies
161 Views
Last post May 21, 2017, 08:59:45 pm
by Cut4fun .
8 Replies
149 Views
Last post December 31, 2018, 09:04:53 am
by Cut4fun .