Author Topic: Poulan Super Micro XXV Deluxe 2.3 piston  (Read 879 times)

0 Members and 1 Guest are viewing this topic.

Offline bcmktg

  • pruner
  • *
  • Posts: 4
  • Karma: 0
  • Location: Loveland, OH 45140
Poulan Super Micro XXV Deluxe 2.3 piston
« on: November 29, 2013, 09:51:11 am »
I've hunted high and low on the internet and I cannot find even an old outdated part number for the piston and/or piston kit for a Poulan Super Micro XXV Deluxe 2.3 c.i. saw.  Bear in mind, the piston is is NOT the same as the one for a regular Micro XXV as they are only 2.0 c.i.  I strongly suspect the piston for the 2300, 2300CVA, and possibly some others, is exactly the same as the one I need, but I have exhausted all efforts to confirm it.  I would very much appreciate any help I can get on this.

Thanks!

Al Babcock
Loveland, OH 45140

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21754
  • Karma: 517
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan Super Micro XXV Deluxe 2.3 piston
« Reply #1 on: November 29, 2013, 10:14:54 am »
Can you post pics of this saw you have?   Poulan Super Micro XXV Deluxe 2.3
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21754
  • Karma: 517
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan Super Micro XXV Deluxe 2.3 piston
« Reply #2 on: November 29, 2013, 10:43:17 am »
Found some pics.


REDNECK Saw Repair Getter Done

Offline bcmktg

  • pruner
  • *
  • Posts: 4
  • Karma: 0
  • Location: Loveland, OH 45140
Re: Poulan Super Micro XXV Deluxe 2.3 piston
« Reply #3 on: November 30, 2013, 01:06:13 am »
Found some pics.

Yup.  That be the one!

Al Babcock
Loveland, OH 45140



Offline fossil

  • 6 cube
  • ****
  • Posts: 198
  • Karma: 59
  • Location: Brampton, Ontario
Re: Poulan Super Micro XXV Deluxe 2.3 piston
« Reply #4 on: November 30, 2013, 10:38:12 am »
If you have the saw apart, can you mic the piston diameter? Some have plated bores and some unplated. I have a cross reference chart and I suspect if it has a plated bore the Cylinder ID would be 1.50" PN 530011245 and the piston OD would be 1.495 PN 530023484.
The 2300 has a plain bore and a chrome plated piston
Just guessing though
Tim

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2108
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan Super Micro XXV Deluxe 2.3 piston
« Reply #5 on: November 30, 2013, 02:04:56 pm »
Some Poulan Pro and Husqvarna Micro variants had chromed bores and bare pistons.  There were, 2.0ci, and 2.3ci versions of these as well.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline moparman texas

  • 4 cube
  • **
  • Posts: 32
  • Karma: 10
  • Location: Texarkana TX
Re: Poulan Super Micro XXV Deluxe 2.3 piston
« Reply #6 on: December 03, 2013, 07:54:41 pm »
The reason that you are having trouble finding a piston for it, is because there is no such model as Poulan Micro XXV Super Deluxe 2.3. Poulan did not make a 2.3 ci version when it was selling the Micro XXV models; the Micro 2.3 ci engine was introduced later. If your engine is 2.3 ci, it's previous owner must have swapped con rod, piston and cylinder. All Poulan Micro saws were bare bore engines, until 2.3 was offered in plated cylinder (2350) and then later in a few late Poulan Pro models. The 2.0 ci engine was never offered in a plated cylinder.

Offline doreadeal

  • 5 cube
  • ***
  • Posts: 83
  • Karma: 3
Re: Poulan Super Micro XXV Deluxe 2.3 piston
« Reply #7 on: December 04, 2013, 07:35:40 am »
I've had a few of these, have a craftsman version now. Can't be any help though, Ive never been inside. I can tell you they love a muffler mod though, they turn into real screamers.

 

Related Topics

  Subject / Started by Replies Last post
38 Replies
1176 Views
Last post June 05, 2013, 09:15:45 pm
by Al Smith
Poulan Micro

Started by fossil « 1 2 » Poulan

14 Replies
447 Views
Last post May 08, 2020, 06:40:50 am
by Cut4fun .
Poulan micro XXV

Started by countryhog « 1 2 » Poulan

10 Replies
510 Views
Last post August 01, 2014, 09:45:30 pm
by Cut4fun .
3 Replies
148 Views
Last post March 01, 2015, 09:28:18 pm
by SquareFile
16 Replies
1417 Views
Last post January 07, 2020, 07:57:44 am
by Super360
37 Replies
1154 Views
Last post June 17, 2017, 09:24:24 am
by Cut4fun .
6 Replies
443 Views
Last post November 16, 2016, 01:09:22 pm
by Cut4fun .
0 Replies
88 Views
Last post June 09, 2017, 02:17:42 pm
by dpjones
8 Replies
269 Views
Last post January 14, 2019, 10:03:10 am
by trappermike
3 Replies
47 Views
Last post April 06, 2020, 07:47:38 am
by Cut4fun .