« previous next »
Pages: [1] 2   Go Down

Author Topic: Poulan Top Handle 1800 woodshark  (Read 251 times)

0 Members and 0 Guests are viewing this topic.

Offline ed 46

  • 3 cube
  • *
  • Posts: 13
  • Karma: 1
Poulan Top Handle 1800 woodshark
« on: October 31, 2014, 02:16:26 pm »
Hi everybody;  I'm confused about the bore diameter on my 1800.  The ring I ordered (530024929) is way too small.  Are the bores of the 2000 and the 1800 the same.  My bore is about 1.257
Logged

Share on Facebook Share on Twitter

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan Top Handle 1800 woodshark
« Reply #1 on: October 31, 2014, 02:20:50 pm »
If you look in the IPL's, you will see references to "type 1", " type 2", "type 3", etc saws.  Some 1800's are actually the same as 2000's (regarding the P/C's).
Logged
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline ed 46

  • 3 cube
  • *
  • Posts: 13
  • Karma: 1
Re: Poulan Top Handle 1800 woodshark
« Reply #2 on: October 31, 2014, 02:30:25 pm »
Ok I'll check it out.  Acres gives the bore size on an 1800 but not a 2000. 
Logged

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan Top Handle 1800 woodshark
« Reply #3 on: October 31, 2014, 02:34:43 pm »
Logged
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22184
  • Karma: 560
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan Top Handle 1800 woodshark
« Reply #4 on: October 31, 2014, 02:35:04 pm »
Quote from: Eccentric on October 31, 2014, 02:20:50 pm
If you look in the IPL's, you will see references to "type 1", " type 2", "type 3", etc saws.  Some 1800's are actually the same as 2000's (regarding the P/C's).

Didnt know that. I always assumed the 1800 was 30cc. Guess I need to pay attention now too.
Logged
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22184
  • Karma: 560
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan Top Handle 1800 woodshark
« Reply #5 on: October 31, 2014, 02:35:44 pm »
I never seen a 1800 super.  Just 1800.

piston

530069545  2000 - T 1, 2 & 3, & Model 1800-T 3 & 4

530010432 1800-T 1 & T 2

Logged
REDNECK Saw Repair Getter Done

Offline ed 46

  • 3 cube
  • *
  • Posts: 13
  • Karma: 1
Re: Poulan Top Handle 1800 woodshark
« Reply #6 on: October 31, 2014, 04:49:03 pm »
Another thing I noticed was that that the wt309 carb on that doesn't have a round bore on the choke side.  It is partially closed off compared to most walbros.  Is it possible that they used the same piston and cylinder on both engines and intentionally restricted the power on the 1800 with the carb?
Logged

Offline ed 46

  • 3 cube
  • *
  • Posts: 13
  • Karma: 1
Re: Poulan Top Handle 1800 woodshark
« Reply #7 on: October 31, 2014, 07:48:49 pm »
Mystery solved somebody switched the covers. It's not an 1800. It's a 2300 av.  Bore 1.525  Stroke 1.250.  Appreciate the input and your patience
I'm still just learning.
Logged

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan Top Handle 1800 woodshark
« Reply #8 on: November 01, 2014, 02:42:22 am »
We all are still learning.8)
Logged
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22184
  • Karma: 560
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan Top Handle 1800 woodshark
« Reply #9 on: November 01, 2014, 09:58:48 am »
I was wondering about poulan 2300AV isnt it 38cc ?   

Poulan 2300 av IPL  http://www.barrettsmallengine.com/partslist/poulan2300avchainsaw.pdf
Logged
REDNECK Saw Repair Getter Done
Pages: [1] 2   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
Poulan 1800

Started by Cut4fun . « 1 2 » Poulan

12 Replies
1213 Views 		Last post December 23, 2013, 06:06:19 pm
by bustedknuckles
16 Replies
1578 Views 		Last post November 02, 2013, 11:05:19 pm
by Oliver1655
5 Replies
290 Views 		Last post December 31, 2012, 04:26:16 pm
by Cut4fun
1 Replies
46 Views 		Last post June 28, 2013, 03:42:14 pm
by Cut4fun .
8 Replies
381 Views 		Last post September 28, 2013, 03:47:02 pm
by Cut4fun .
5 Replies
138 Views 		Last post September 21, 2014, 09:58:50 am
by stubnail67
14 Replies
388 Views 		Last post January 12, 2015, 02:23:43 pm
by countryhog
12 Replies
265 Views 		Last post October 14, 2016, 07:03:38 pm
by dannyupsolate
1 Replies
115 Views 		Last post January 15, 2017, 03:44:55 pm
by Cut4fun .
0 Replies
58 Views 		Last post April 23, 2020, 01:10:19 pm
by Cut4fun .