Author Topic: poulan xx parts interchangeability  (Read 129 times)

0 Members and 0 Guests are viewing this topic.

Online pete

  • Piped Saw
  • *****
  • Posts: 493
  • Karma: 37
poulan xx parts interchangeability
« on: April 01, 2015, 07:32:37 am »
Hi all a friend dropped by today with a nice little poulan xx he scored at a swapmeet and wanted to know if I had a flywheel and starter dogs   I have some xxv poulans  will any parts change over I know very little of the poulans just grab them as trade material if I see them cheap thanks

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21860
  • Karma: 521
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: poulan xx parts interchangeability
« Reply #1 on: April 02, 2015, 01:15:46 pm »
My post didnt post yesterday  ??? .

I had IPL's for XX 20 20D XXV older and XXV micro.   Just compare the IPL's and part numbers and you should get your info.
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: poulan xx parts interchangeability
« Reply #2 on: April 02, 2015, 03:21:22 pm »
Don't think there's much of anything that swaps between the XX series and either the Micro series or the XXV series.  They flywheel and starter parts are most likely unique to the XX.  The starter system on those is very different from what's on the other two families.

I have seen some listings in catalogs (such as Oregon) that show the same clutch drum working for the XX and Micro series, but I have yet to verify it. 

The bar mount is the same between the three saw families.....
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Online pete

  • Piped Saw
  • *****
  • Posts: 493
  • Karma: 37
Re: poulan xx parts interchangeability
« Reply #3 on: April 02, 2015, 08:24:00 pm »
Thanks guys will try get those ipls up to view

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: poulan xx parts interchangeability
« Reply #4 on: April 02, 2015, 11:06:12 pm »
Try www.barrettsmallengine.com for the IPL's.  The IPL's for the XX saws are listed as "20" and "20D".

http://www.barrettsmallengine.com/poulan/chainsawpartslist.html
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Online pete

  • Piped Saw
  • *****
  • Posts: 493
  • Karma: 37
Re: poulan xx parts interchangeability
« Reply #5 on: April 03, 2015, 07:47:55 am »
Thanks will check it out

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
371 Views
Last post June 11, 2011, 05:25:29 pm
by Cut4fun
2 Replies
413 Views
Last post February 08, 2013, 10:51:18 pm
by mattinky
29 Replies
748 Views
Last post February 02, 2016, 01:39:22 pm
by mowertech
1 Replies
270 Views
Last post June 08, 2014, 08:01:59 am
by jmester
111 Replies
1291 Views
Last post September 27, 2015, 09:41:29 pm
by 3000 FPS
6 Replies
112 Views
Last post January 29, 2015, 02:25:42 pm
by Eccentric
38 Replies
868 Views
Last post June 21, 2016, 01:32:54 pm
by Cut4fun .
13 Replies
279 Views
Last post November 05, 2018, 07:41:57 am
by Cut4fun
1 Replies
141 Views
Last post April 30, 2019, 11:23:42 am
by Cut4fun .
29 Replies
266 Views
Last post June 28, 2020, 12:12:49 am
by 3000 FPS