« previous next »
Pages: 1 2 [3]   Go Down

Author Topic: Poulans FS  (Read 753 times)

0 Members and 25 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23740
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulans FS
« Reply #20 on: December 08, 2017, 11:24:57 am »
Big box just arrived.  Will take a look see in a bit. 
Least up to 24 degrees now.
Logged

Offline Tractorsaw1

  • 6 cube
  • ****
  • Posts: 183
  • Karma: 25
  • Location: SHOW ME MO

    • Total Badges: 21
    Badges: (View All)
    Level 5 Fourth year Anniversary Third year Anniversary Avatar Level 4 Second year Anniversary
Re: Poulans FS
« Reply #21 on: December 08, 2017, 11:42:13 am »
Excellent!  Loaded the wood furnace & left for work this am 18° here :)  I did find I have an Oregon 18" bar so no worries on swapping it out.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23740
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulans FS
« Reply #22 on: December 08, 2017, 12:35:36 pm »
Got the torpedo heater filled and cranking. Got cold just putting a part on a saw.
Logged

Offline HolmenTree

  • Nitro Hotsaw
  • *******
  • Posts: 1382
  • Karma: 199
  • Location: Manitoba Canada

    • Total Badges: 34
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 6 1000 Posts Seventh year Anniversary
Re: Poulans FS
« Reply #23 on: December 08, 2017, 02:04:09 pm »
Had my heat set at 60F fulltime since early Oct. :D
Logged
Making a living with a saw since age 16.
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23740
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulans FS
« Reply #24 on: December 08, 2017, 02:59:40 pm »
PP330 psi feels goooood and saw looks good IMO. 

20" laminated bar.   Not seeing a 18" K041 or K095 here but will look again when done working on truck.

Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23740
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulans FS
« Reply #25 on: December 08, 2017, 05:46:54 pm »
Just finished truck so didnt get chance to look. Will look for a 18 before I start packing 330 sat-sun
Logged

Offline Tractorsaw1

  • 6 cube
  • ****
  • Posts: 183
  • Karma: 25
  • Location: SHOW ME MO

    • Total Badges: 21
    Badges: (View All)
    Level 5 Fourth year Anniversary Third year Anniversary Avatar Level 4 Second year Anniversary
Re: Poulans FS
« Reply #26 on: December 29, 2017, 06:00:46 pm »
Ran the 330 today. Cut a 16” dead elm. I think it’s a little fat but forgot my screw driver. Didn’t seem as zippy as my last 330 but had good torque. Was going to get a video of the last cut but phone don’t like the cold. Going to work up an oak tomorrow afternoon with my screw driver
Logged
Like Like x 1 View List
Pages: 1 2 [3]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
Date these Poulans

Started by Cut4fun « 1 2 3 » Poulan

26 Replies
2066 Views 		Last post September 13, 2015, 12:03:49 pm
by Cut4fun .
1 Replies
646 Views 		Last post September 29, 2012, 09:23:33 pm
by 660magnum
2 Replies
231 Views 		Last post February 11, 2013, 09:29:02 pm
by ms460woodchuck
0 Replies
276 Views 		Last post June 20, 2015, 12:02:22 pm
by Cut4fun .