Author Topic: Craftsman 358357180  (Read 186 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21891
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Craftsman 358357180
« Reply #10 on: January 06, 2020, 12:40:29 pm »
She looks good, is it true that these saws need 16:1?

No  I run 40:1 in everything. 
REDNECK Saw Repair Getter Done
Agree Agree x 1 View List

Offline Super360

  • 3 cube
  • *
  • Posts: 16
  • Karma: 3
Re: Craftsman 358357180
« Reply #11 on: January 06, 2020, 12:53:03 pm »
not really looking to buy one but thanks.

Offline Super360

  • 3 cube
  • *
  • Posts: 16
  • Karma: 3
Re: Craftsman 358357180
« Reply #12 on: January 06, 2020, 12:55:11 pm »
I would need the 530019059 seals for this chainsaw?

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21891
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Craftsman 358357180
« Reply #13 on: January 06, 2020, 01:08:51 pm »
I would need the 530019059 seals for this chainsaw?

Yep  F/W & PTO seals: 530019059. Homelite 94638. SKF 4913. Homelite 07025.
REDNECK Saw Repair Getter Done
Agree Agree x 1 View List

Offline Super360

  • 3 cube
  • *
  • Posts: 16
  • Karma: 3
Re: Craftsman 358357180
« Reply #14 on: January 06, 2020, 10:30:55 pm »
Hey one more question if ya dont mind. I repaired the oiler with a new duckbill(the one that is behind the clutch). I was wondering is that screen necessary because i grinded it off with a machine.
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21891
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Craftsman 358357180
« Reply #15 on: January 07, 2020, 07:50:32 am »
Hey one more question if ya dont mind. I repaired the oiler with a new duckbill(the one that is behind the clutch). I was wondering is that screen necessary because i grinded it off with a machine.

I never had to repair one as I have plenty of good used from parts saws.

But here is a thread on the info. http://chainsawrepair.createaforum.com/poulan/check-valve-poulan-micro-saws/msg56716/#msg56716
REDNECK Saw Repair Getter Done
Winner Winner x 1 View List

Offline AmericanPsycho

  • 6 cube
  • ****
  • Posts: 177
  • Karma: 5
  • Kendallville's Resident Chainsaw Maniac
  • Location: Redneckville, IN
Re: Craftsman 358357180
« Reply #16 on: January 07, 2020, 07:19:41 pm »
She looks good, is it true that these saws need 16:1?

Negatron. That ratio is with actual motor oil. Using a good synthetic 2-cycle oil you can run that saw on 50:1 with carb properly tuned.
From darkness to light and back again.
Winner Winner x 1 View List

Offline Super360

  • 3 cube
  • *
  • Posts: 16
  • Karma: 3
Re: Craftsman 358357180
« Reply #17 on: January 08, 2020, 02:39:59 am »
So is it true that 50:1 is just some epa crap then? It seems people like 40:1 more than 50:1.
Agree Agree x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21891
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Craftsman 358357180
« Reply #18 on: January 08, 2020, 07:43:09 am »
So is it true that 50:1 is just some epa crap then? It seems people like 40:1 more than 50:1.

To me 50:1 is  EPA BS.   I wont run at that ratio myself.

Dealers have to tell you to run the 50 ratio ;) and they like selling you OPE
REDNECK Saw Repair Getter Done
Like Like x 2 View List

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4461
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: Craftsman 358357180
« Reply #19 on: January 08, 2020, 11:30:24 pm »
I would never run 50-1 either.    You know it is not only the cylinder and rings that depend on that oil but the rod bearings and crank bearings.
There have been some early failures on bearings because of the lack of oil. 
PP 505, 475, 445.
Like Like x 1 Agree Agree x 1 View List

 

Related Topics

  Subject / Started by Replies Last post
2 Replies
1163 Views
Last post July 18, 2012, 01:40:02 pm
by Cut4fun .
104 Replies
2296 Views
Last post June 05, 2019, 10:51:03 am
by Cut4fun .
5 Replies
240 Views
Last post February 11, 2014, 03:36:38 pm
by Cut4fun
3 Replies
768 Views
Last post July 13, 2015, 12:41:04 am
by Eccentric
4 Replies
149 Views
Last post December 21, 2014, 08:08:43 pm
by AmericanPsycho
5 Replies
386 Views
Last post March 06, 2017, 09:49:31 pm
by 3000 FPS
16 Replies
405 Views
Last post February 15, 2016, 11:25:49 pm
by dannyupsolate
1 Replies
445 Views
Last post April 03, 2016, 12:34:02 pm
by Cut4fun .
4 Replies
103 Views
Last post April 11, 2018, 03:05:30 pm
by Revpop
3 Replies
52 Views
Last post May 07, 2020, 10:00:44 pm
by Super360