« previous next »
Pages: [1]   Go Down

Author Topic: Flywheel Id.  (Read 341 times)

0 Members and 0 Guests are viewing this topic.

Offline dpjones

  • 5 cube
  • ***
  • Posts: 131
  • Karma: 18
Flywheel Id.
« on: February 05, 2018, 07:21:12 pm »
I got these flywheels mixed up. They are from a PP4620 a Craftsman 358.350203 and a 40cc poulan that all was on it was Super Clean on the starter cover, it has the blue tube feeding air to carb.

In the picture the straight finned is three magnet and the curve fin is two magnet, have two of them

The flywheels are the same size even though they don't look like it in the picture

I'm building two saws from the parts, Craftsman is running now

Thanks
DJ
Logged

Share on Facebook Share on Twitter

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4688
  • Karma: 319
  • Location: Carpenter, Wyoming
Re: Flywheel Id.
« Reply #1 on: February 05, 2018, 09:35:24 pm »
I have a 4620 out in the garage.   If I get a chance I will look tomorrow at the flywheel.

I am thinking it will be the one on the left in your pictures that you posted.
Logged
PP 505, 475, 445.
Like Like x 1 View List

Offline dpjones

  • 5 cube
  • ***
  • Posts: 131
  • Karma: 18
Re: Flywheel Id.
« Reply #2 on: February 05, 2018, 10:19:28 pm »
That's the one I put on the craftsman and it runs but I was wondering if the straight fin was for the super clean that had the blue tube.

I mixed these up a few months back and my memory is no good a few minutes back and getting worse.

Thanks
Logged
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23413
  • Karma: 661
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Flywheel Id.
« Reply #3 on: February 06, 2018, 07:35:44 am »
 358.350203  Compatibility

Craftsman
358351191 Gas Chainsaw
358.350203 Chainsaw
358348231 Chainsaw
358350200 Chainsaw
944411461 Chainsaw
358351210 Chainsaw
358356242 Gas Chainsaw
358356240 Gas Chainsaw
358356241 Gas Chainsaw
944414460 Chainsaw
358348232 Chainsaw
944411462 Gas Chainsaw
358350202 Chainsaw
358348230 Chainsaw
358350201 Chainsaw
358350203 Chainsaw
358381600 Chainsaw



Logged
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23413
  • Karma: 661
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Flywheel Id.
« Reply #4 on: February 06, 2018, 07:39:53 am »
I dont see the one on the right in IPL
Logged

Offline dpjones

  • 5 cube
  • ***
  • Posts: 131
  • Karma: 18
Re: Flywheel Id.
« Reply #5 on: February 06, 2018, 12:45:46 pm »
I couldn't find it either and it is a 3 magnet, the right one is 2 magnet. I figured they would use different coils with more or less magnets and they got to be a reason for the straight fins.

The only number on the right one is 20370-01-PW

I read some where one time about the 2 and 3 magnet flywheel but don't remember what are where I read it
Logged
Like Like x 1 View List

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4688
  • Karma: 319
  • Location: Carpenter, Wyoming
Re: Flywheel Id.
« Reply #6 on: February 06, 2018, 06:14:19 pm »
So I looked and like Cut4fun pointed out the flywheel with the curved fins is the one for the PP4620.
Logged
PP 505, 475, 445.

Offline dpjones

  • 5 cube
  • ***
  • Posts: 131
  • Karma: 18
Re: Flywheel Id.
« Reply #7 on: February 06, 2018, 06:36:29 pm »
Thanks for looking, I guess I got the craftsman right, I run two tanks of gas through it a little bit ago and it seemed ok, I used a curved fin 3 magnet on it, I did find a straight fin on ebay and it said it fit a PP255. This stuff could've been mixed up parts and thrown together before I got it and all three saws were giving to me, just something to do, sure are a lot of different Poulans though.

Thanks Again for the help
DJ
Logged
Like Like x 1 View List
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
0 Replies
240 Views 		Last post March 26, 2012, 08:02:32 pm
by Snoopy
6 Replies
850 Views 		Last post October 14, 2012, 02:20:05 pm
by Jim372xp
3 Replies
454 Views 		Last post January 17, 2013, 07:33:10 pm
by jmester
p 41 flywheel

Started by Bob « 1 2 » Pioneer

15 Replies
1718 Views 		Last post June 05, 2014, 08:49:36 pm
by KilliansRedLeo
31 Replies
1032 Views 		Last post November 25, 2014, 07:12:07 am
by Al Smith
15 Replies
759 Views 		Last post December 05, 2014, 01:30:49 pm
by aclarke
0 Replies
118 Views 		Last post February 22, 2015, 06:58:50 pm
by adam32
0 Replies
202 Views 		Last post May 09, 2017, 08:00:12 am
by chy_farm
0 Replies
261 Views 		Last post August 10, 2018, 10:11:15 pm
by Kalcorp
2 Replies
205 Views 		Last post May 23, 2020, 04:59:08 pm
by Gregg MacPherson