Author Topic: Poulan S25 AV  (Read 386 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22076
  • Karma: 548
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan S25 AV
« Reply #10 on: October 22, 2014, 07:11:24 pm »
Poulan S25 AV   I am looking at one and it looks like the AV is only on the top handle and none on the rear handle.  Right?









Be a nice one for your son Ron.  $85
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan S25 AV
« Reply #11 on: October 26, 2014, 04:25:46 am »
That's right Kevin.  AV on the handlebar only. The only XXV series saws with full AV are the 25-CVA and S25 - CVA.

Same distinction with the Micro series saws.  AV branded models only have AV on the handlebar.  CVA models (and the 2100/2400/PP236 rear handle saws) have full AV.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2757
  • Karma: 172
Re: Poulan S25 AV
« Reply #12 on: October 26, 2014, 05:30:04 am »
Speaking of which,S-25 ,I have one giving me fits. It belongs to my wifes' cousin.

I've had that thing nearly field stripped .Rebuilt the carb,new fuel lines ,plug ,checked the timing ,flipped the reed ..At best I get a poof and have ignited that little rascal  about 3 or 4 times from fuel build up,stub,no muffler  .

All I can think of is a funky condenser which can cause real strange things to happen .At the moment it's been banned to the shelf until I get my composuer back lest I run over it with my bulldozer .

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: Poulan S25 AV
« Reply #13 on: October 26, 2014, 06:01:14 am »
HAHA Al. Sometimes I have to walk away too.
Ron

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22076
  • Karma: 548
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan S25 AV
« Reply #14 on: October 26, 2014, 09:16:22 am »
Al if you need parts holler.  Condenser etc here on shelf.
REDNECK Saw Repair Getter Done

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2757
  • Karma: 172
Re: Poulan S25 AV
« Reply #15 on: October 26, 2014, 09:11:47 pm »
Thanks but I have to get over my pout first . ;D Ha once I got a case of the red azz at a Stihl and that SOB sat on the shelf two years before I calmed down .

The thing about those dang condensers is with the plug out you might get a nice blue spark,looks good .However once you get it above cranking speed it can do funny things .I just went through this on my old Jeep .

Odd in both cases if that is the case .Usually the condenser is either good or bad,spark or no spark .Maybe the condenser witch has been sneaking around my place . :D

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan S25 AV
« Reply #16 on: October 27, 2014, 04:31:43 pm »
Condenser gets my vote too.

Re the'put it on the shelf before I smas it' situation.............. been there many times.  Right now I have a guy's Mac 4-30A in the corner........to keep it from being smashed with an 8 pound sledge...
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

 

Related Topics

  Subject / Started by Replies Last post
17 Replies
772 Views
Last post May 24, 2017, 06:52:22 pm
by 3000 FPS
Poulan 445

Started by 3000 FPS « 1 2 ... 18 19 » Poulan

181 Replies
4601 Views
Last post August 01, 2020, 08:05:18 am
by Cut4fun
7 Replies
521 Views
Last post April 13, 2014, 08:11:42 pm
by Cut4fun .
0 Replies
192 Views
Last post October 02, 2012, 11:36:18 am
by mweba
Poulan 395

Started by 3000 FPS « 1 2 3 » Poulan

23 Replies
982 Views
Last post January 05, 2013, 09:09:29 pm
by 3000 FPS
4 Replies
555 Views
Last post November 23, 2012, 12:28:15 am
by Andyshine77
23 Replies
1248 Views
Last post November 02, 2015, 04:36:50 pm
by Cut4fun .
Poulan 335

Started by 3000 FPS « 1 2 3 4 5 » Poulan

46 Replies
1326 Views
Last post February 14, 2020, 09:23:59 am
by Cut4fun .
Poulan 380

Started by Cut4fun . « 1 2 ... 7 8 » Poulan

78 Replies
2137 Views
Last post March 01, 2020, 08:06:34 am
by Cut4fun .
poulan saw

Started by Jay Poulan

2 Replies
197 Views
Last post May 24, 2013, 05:07:22 pm
by Cut4fun .