Author Topic: Vapor lock on a hot day.  (Read 1356 times)

0 Members and 9 Guests are viewing this topic.

Offline fossil

  • 6 cube
  • ****
  • Posts: 205
  • Karma: 66
  • Location: Brampton, Ontario

  • Total Badges: 28
    Badges: (View All)
    Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary
Re: Vapor lock on a hot day.
« Reply #10 on: November 02, 2016, 08:57:00 pm »
Gas boils at temperatures from 95F to 400F. The tank vent is important as a vacuum in the tank will lower the boiling point considerably. Make sure the vent is letting air in and not out. When the cap is removed you can hear the hiss of air. The question is which way is it going. Not recommended to check with a match unless you have a willing friend handy.
Higher elevations just make the issue worse. Winter formulated gas does as well.

Cory, if you run the tank dry, fill it up, cap it and shake the saw for a bit. That will build pressure in the tank and get the gas up to the carb faster,

I also have some filters I bought from Carbtech that have check valves of some kind in them to keep the gas from draining back.
Tim
Like Like x 1 View List

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2779
  • Karma: 181

  • Total Badges: 34
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 6 Seventh year Anniversary Sixth year Anniversary
Re: Vapor lock on a hot day.
« Reply #11 on: November 02, 2016, 09:06:45 pm »
Funny part about that hot weather .I had a cooler full of cold water and drank at least a half dozen during that day never peed once .
Like Like x 1 View List

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

  • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Vapor lock on a hot day.
« Reply #12 on: November 02, 2016, 10:49:42 pm »
Funny part about that hot weather .I had a cooler full of cold water and drank at least a half dozen during that day never peed once .

That is funny Al but I have to admit to the same experience.   Sweat it out instead.
PP 505, 475, 445.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

  • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Vapor lock on a hot day.
« Reply #13 on: November 02, 2016, 10:54:20 pm »
Gas boils at temperatures from 95F to 400F. The tank vent is important as a vacuum in the tank will lower the coiling point considerably. Make sure the vent is letting air in and not out. When the cap is removed you can hear the hiss of air. The question is which way is it going. Not recommended to check with a match unless you have a willing friend handy.
Higher elevations just make the issue worse. Winter formulated gas does as well.

Cory, if you run the tank dry, fill it up, cap it and shake the saw for a bit. That will build pressure in the tank and get the gas up to the carb faster,

I also have some filters I bought from Carbtech that have check valves of some kind in them to keep the gas from draining back.

I think that in the future I will just ovoid cutting up that high in the mountains when I know it is going to be hot.   Some saws could be more inclined to have this problem than others but I think it will eventually happen to any saw when the right conditions are met.   

I like your tip Tim about shaking the saw to get pressure built up in it and driving fuel up to the carb.
PP 505, 475, 445.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2117
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northwestern Wyoming

  • Total Badges: 37
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: Vapor lock on a hot day.
« Reply #14 on: November 06, 2016, 05:03:00 pm »
Gas boils at temperatures from 95F to 400F. The tank vent is important as a vacuum in the tank will lower the boiling point considerably. Make sure the vent is letting air in and not out. When the cap is removed you can hear the hiss of air. The question is which way is it going. Not recommended to check with a match unless you have a willing friend handy.
Higher elevations just make the issue worse. Winter formulated gas does as well.

Cory, if you run the tank dry, fill it up, cap it and shake the saw for a bit. That will build pressure in the tank and get the gas up to the carb faster,

I also have some filters I bought from Carbtech that have check valves of some kind in them to keep the gas from draining back.

The OEM Poulan 5200/5400/8500 fuel filter is like that.  Is Carbtech the site with the cheap carb rebuild and DG kits?  I need to check out those filters....

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2117
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northwestern Wyoming

  • Total Badges: 37
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: Vapor lock on a hot day.
« Reply #15 on: November 06, 2016, 05:04:02 pm »
This is the site I was thinking of.


http://www.carbtech21.com/Default.asp
Informative Informative x 1 View List

 

Related Topics

  Subject / Started by Replies Last post
8 Replies
545 Views
Last post January 12, 2014, 05:59:02 pm
by weimedog
4 Replies
420 Views
Last post March 23, 2015, 11:07:12 pm
by Hoggwood
4 Replies
239 Views
Last post February 23, 2017, 03:31:11 pm
by dutchsawdoctor
1 Replies
639 Views
Last post March 08, 2019, 09:18:46 am
by Cut4fun .