« previous next »
Pages: 1 2 3 4 [5] 6   Go Down

Author Topic: Poulan 3300  (Read 3839 times)

0 Members and 0 Guests are viewing this topic.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4695
  • Karma: 320
  • Location: Carpenter, Wyoming
Re: Poulan 3300
« Reply #40 on: January 24, 2019, 09:50:20 pm »
I have never owned one.   
Logged
PP 505, 475, 445.
Like Like x 1 View List

Online ray benson

  • 6 cube
  • ****
  • Posts: 186
  • Karma: 95
  • Retired Industrial Electrician
  • Location: Indiana
Re: Poulan 3300
« Reply #41 on: January 25, 2019, 08:54:09 am »
 Poulan doesn't say what max rpm is in the service manual or owners manual.
Initial adjustment of high- and lowspeed mixture needles is one turn open
from a lightly seated position. Make final adjustment with engine running
at operating temperature. Adjust low- speed mixture needle  so engine will accelerate without hesitation.
Adjust high-speed mixture needle to obtain optimum full throttle
performance under cutting load. Do not operate saw with high speed mixture
setting too lean (needle turned too far clockwise as engine damage could result
from lack of lubrication and overheating.
Adjust idle speed screw so engine idles just below clutch engagement speed.

Logged
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23514
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3300
« Reply #42 on: January 25, 2019, 09:51:54 am »
He showed me video of it running with top I sent and 12-12.5 seemed perfect
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23514
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3300
« Reply #43 on: March 17, 2019, 10:49:19 am »
Finally put dads bought new poulan 3300 (maybe 93) and bought new TH mac (maybe 79-81) on the bench yesterday. Going to clean them up. Make sure running order and shelf them because they were dads.

The little poulan 2000 I gave him that I bought in 94 is already cleaned back up and being used pruning again this year. It had replaced that mac TH I despised using.

Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23514
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3300
« Reply #44 on: March 19, 2019, 07:54:52 pm »
Dads poulan 3300 54cc he bought new in 1993 is cleaned up and ready for the shelf. Just purrs like a kitten idling forever and turns into a mad hornet.

Will just get it down from time to time to use and keep it going.

Made me smile and feel good about it.

Now to finish that little mac TH 130 I hated with a passion. Bought new in 79-81

 
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23514
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3300
« Reply #45 on: March 20, 2019, 08:04:59 am »
Dads 3300 on a tear down I did for him many years ago. av's, intake boot, lines, etc. Normal up keep over the years. Topend always looked great.

Logged

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4616
  • Karma: 216
  • OHIO REDNECK
Re: Poulan 3300
« Reply #46 on: March 20, 2019, 08:10:48 am »
Just going to save this here.  Dad  = That thing looks great.  You would not believe the hours we spent out here together cutting trees. I'm glad you have it.
Thanks for cleaning her up.

Logged
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23514
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3300
« Reply #47 on: April 29, 2019, 01:32:05 pm »
3300 saw I bought just for the parts mainly. Nice 335 recoil cover was on it and nice p+c. Just pulled it down to see what all it needed. Now prob just set on shelf being I got plenty of 54cc runners.


Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23514
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3300
« Reply #48 on: April 06, 2020, 01:37:39 pm »
I wasn’t going to redo this 54cc 3300. Supposed to be running parts saw I bought in pieces with yellow 335 recoil. Just wanted it for the parts for my dads bought new 3300 .

Found few more recoils and those nla pulleys too. 330 3450 380  3750  and 365 3500


Logged
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23514
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan 3300
« Reply #49 on: April 07, 2020, 03:33:36 pm »
 3 pulls fired on choke. Now to put a bar chain and test. Type3 later has some things different then dads Type1 that made me pull tank back off for a redo. 😒😋😂
No photo description available.


Got surprise. I put 16” 325 but someone had put a 3/8 rim. So 16” 3/8 k041 bar it is.
So far running cutting great.
Even though I won’t leave 3/8 set up on it.

Some more parts for guys asking.



Logged
Pages: 1 2 3 4 [5] 6   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
1 Replies
581 Views 		Last post December 11, 2012, 04:27:45 pm
by Cut4fun .
44 Replies
2806 Views 		Last post July 26, 2015, 05:45:30 pm
by Cut4fun .
3 Replies
778 Views 		Last post February 03, 2013, 06:33:10 pm
by 660magnum
6 Replies
650 Views 		Last post September 12, 2014, 01:39:38 pm
by Cut4fun .
11 Replies
542 Views 		Last post January 06, 2015, 01:06:57 pm
by Cut4fun .
11 Replies
950 Views 		Last post June 08, 2016, 01:58:07 pm
by Cut4fun
3 Replies
704 Views 		Last post July 13, 2016, 02:28:19 am
by Hoggwood
2 Replies
924 Views 		Last post September 21, 2017, 10:17:09 am
by hillpc
0 Replies
130 Views 		Last post February 13, 2021, 08:08:23 am
by Cut4fun
1 Replies
149 Views 		Last post June 02, 2022, 04:35:23 pm
by ssidwell