Author Topic: Wild Thing  (Read 350 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22033
  • Karma: 544
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Wild Thing
« Reply #10 on: August 15, 2014, 11:54:15 am »
I'm going to take some pics when I start draining the mix and bar oil etc.  Maybe today I hope.  Unless family arrive earlier then thought.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22033
  • Karma: 544
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Wild Thing
« Reply #11 on: August 15, 2014, 02:34:37 pm »
I set it fat rich with my 32:1  I would not go 50:1 JMO get the poulan mix at 40:1 and you should be happy. If to rich with 40 or 50 might need to turn in H just a hair. But test and make sure first.

Got a video loading too. Just showing running and perfect when leaving me. Pressed primer 5-6 times, pulled choke on, 3rd pull popped, pushed choke in and 1 pull running.







REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22033
  • Karma: 544
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Wild Thing
« Reply #12 on: August 15, 2014, 02:53:35 pm »
REDNECK Saw Repair Getter Done

Offline WildThang098

  • 3 cube
  • *
  • Posts: 10
  • Karma: 1
Re: Wild Thing
« Reply #13 on: August 15, 2014, 05:06:13 pm »
Good deal  ;D Thanks for the updates I gotta get to the basement and get my current "wife throwing junk in it" room turned into my saw shop Haha.

Offline WildThang098

  • 3 cube
  • *
  • Posts: 10
  • Karma: 1
Re: Wild Thing
« Reply #14 on: August 15, 2014, 05:45:34 pm »

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Wild Thing
« Reply #15 on: August 15, 2014, 06:35:00 pm »
It was 'for' the owner of this site being suspected of scamming you over a $50 saw...
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline WildThang098

  • 3 cube
  • *
  • Posts: 10
  • Karma: 1
Re: Wild Thing
« Reply #16 on: August 15, 2014, 06:58:19 pm »
Ohh. haha I wasnt really accusing him ,I just asked him if it was to assure it wasnt. Im new to the site . I have always used my old mans Stihls so not new to chainsaws but this will be the first I actually try to mod and tinker with one alittle.

 

Related Topics

  Subject / Started by Replies Last post
13 Replies
1189 Views
Last post February 09, 2013, 09:08:05 am
by farmboy
6 Replies
346 Views
Last post January 30, 2013, 08:49:25 am
by oldpart
27 Replies
961 Views
Last post March 12, 2020, 10:52:36 am
by Cut4fun .
16 Replies
412 Views
Last post September 20, 2013, 05:17:00 pm
by Cut4fun
5 Replies
598 Views
Last post August 27, 2015, 02:22:03 pm
by Cut4fun .
9 Replies
303 Views
Last post February 02, 2014, 10:24:24 am
by countryhog
4 Replies
339 Views
Last post April 22, 2014, 08:57:25 am
by KilliansRedLeo
7 Replies
274 Views
Last post September 30, 2015, 07:01:05 pm
by treeslayer2003
0 Replies
187 Views
Last post July 12, 2014, 12:23:03 pm
by KilliansRedLeo
7 Replies
186 Views
Last post January 31, 2018, 03:02:37 pm
by Cut4fun .