Author Topic: Solo 665 Closed Quad Port Cylinder  (Read 649 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 3700
  • Karma: 133
  • OHIO REDNECK
Re: Solo 665 Closed Quad Port Cylinder
« Reply #10 on: July 09, 2014, 02:15:09 pm »
key points from above.

At first you will think that it is built by Dolmar. That is not the case. This saw is built by Solo. Solo does sell the large Dolmar 9010, they call it the 694 but the 681 and its smaller sisters 675, 665 are Solo built.

From what I understand is that Dolmar did not design all of the 7900. Solo designed a lot of the parts for that saw. They were to be sold together in joint venture like the large Dolmar 9010.

Dolmar took all of the credit for the 7900 and Solo got the shaft.

Solo took it one step farther and made the same basic saw with a larger engine and a few improvements.
REDNECK Saw Repair

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 17847
  • Karma: 334
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Solo 665 Closed Quad Port Cylinder
« Reply #11 on: July 09, 2014, 03:00:10 pm »
Dang Tim you going to share all those Solo boxes in front of your house.   ;D ;) 8)
REDNECK Saw Repair Getter Done

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Solo 665 Closed Quad Port Cylinder
« Reply #12 on: July 09, 2014, 05:07:37 pm »
That is actually the door to the shop not my home. Yes, I did not keep even one for myself. Unless something changes they are all already sold.  Randy Evens wants one, Adam Artzer wants 2 and the other six went to guys on FHC. They are all new with warranty but no bars. To my knowledge they were the only ones left in the country. Even Solo in VA does not have any nor can they get any. I suspect Adam Artzer wants them for the stroked crank but don't know.
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline adam32

  • Piped Saw
  • *****
  • Posts: 422
  • Karma: 44
Re: Solo 665 Closed Quad Port Cylinder
« Reply #13 on: July 09, 2014, 05:31:59 pm »
That is actually the door to the shop not my home. Yes, I did not keep even one for myself. Unless something changes they are all already sold.  Randy Evens wants one, Adam Artzer wants 2 and the other six went to guys on FHC. They are all new with warranty but no bars. To my knowledge they were the only ones left in the country. Even Solo in VA does not have any nor can they get any. I suspect Adam Artzer wants them for the stroked crank but don't know.

Yeah probably one into a 4 cube racer (even tho its a tiny bit over) and the other either I'll port and make it into a work saw or send it to Adam Clarke for a 7900 top end racer...

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 17847
  • Karma: 334
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Solo 665 Closed Quad Port Cylinder
« Reply #14 on: July 09, 2014, 06:03:49 pm »
Tim, nice shop then too.
REDNECK Saw Repair Getter Done

Offline DexterDay

  • 4 cube
  • **
  • Posts: 49
  • Karma: 8
Re: Solo 665 Closed Quad Port Cylinder
« Reply #15 on: July 11, 2014, 11:12:16 pm »
That is actually the door to the shop not my home. Yes, I did not keep even one for myself. Unless something changes they are all already sold.  Randy Evens wants one, Adam Artzer wants 2 and the other six went to guys on FHC. They are all new with warranty but no bars. To my knowledge they were the only ones left in the country. Even Solo in VA does not have any nor can they get any. I suspect Adam Artzer wants them for the stroked crank but don't know.

I thank you again for making one of these available to me.  ;D

Lots of good info here on these saws.  :)
Mastermind'd Stihl MS 261C-M
Mastermind'd Stihl MS 460
MasterMind'd Stihl MS 461
MasterMind'd Stihl Jonsered 2171

 

Related Topics

  Subject / Started by Replies Last post
9 Replies
498 Views
Last post January 31, 2012, 09:28:50 pm
by Al Smith
3 Replies
754 Views
Last post June 22, 2012, 10:47:14 pm
by farmboy
19 Replies
2259 Views
Last post October 19, 2013, 06:25:02 pm
by Cut4fun .
100 Replies
846 Views
Last post February 24, 2013, 12:54:05 pm
by jmester
4 Replies
237 Views
Last post July 02, 2013, 09:47:32 pm
by farmboy
13 Replies
533 Views
Last post August 28, 2014, 12:10:52 pm
by Cut4fun .
17 Replies
295 Views
Last post January 15, 2015, 08:37:19 am
by Duke Thieroff
24 Replies
284 Views
Last post January 26, 2015, 08:30:50 pm
by Cut4fun .
5 Replies
313 Views
Last post October 30, 2015, 04:48:09 pm
by dboyd351
0 Replies
289 Views
Last post April 07, 2016, 01:41:04 pm
by Cut4fun .