Author Topic: Solo 680 piston  (Read 3940 times)

0 Members and 0 Guests are viewing this topic.

Offline Riddler1100

  • 3 cube
  • *
  • Posts: 7
  • Karma: 1
Solo 680 piston
« on: March 19, 2015, 07:54:52 pm »
Hi I'm trying to find a solo 680 piston, may possibly need cylinder head also haven't pulled it apart yet. I'm located in Australia

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23976
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Solo 680 piston
« Reply #1 on: March 19, 2015, 08:05:19 pm »
Ideas

I've put 064 pistons in Solo 680's and just recently was toying with a BB044 piston and one other that I can't remember in a stroked 680...



Adam is the guy into the solo

Offline adam32

  • Piped Saw
  • *****
  • Posts: 429
  • Karma: 46
Re: Solo 680 piston
« Reply #2 on: March 19, 2015, 09:43:10 pm »
Yup. A Stihl 064 piston fits with a little work to clear the rod end.

Offline Riddler1100

  • 3 cube
  • *
  • Posts: 7
  • Karma: 1
Re: Solo 680 piston
« Reply #3 on: March 20, 2015, 02:52:50 am »
What kind of modifying is required?? To use the 064 piston

Offline adam32

  • Piped Saw
  • *****
  • Posts: 429
  • Karma: 46
Re: Solo 680 piston
« Reply #4 on: March 20, 2015, 10:10:55 am »
What kind of modifying is required?? To use the 064 piston

Use a flat file and relieve the inside of the piston bosses where the rod goes in. The rod on the 680 is wider then the Stihl. Pretty easy, takes about 15 minutes. Its hard to explain but once you see it its is pretty obvious.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23976
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Solo 680 piston
« Reply #5 on: March 20, 2015, 12:44:17 pm »
I have to open wrist pin bosses to run the stihl 066 pistons in my poulan 505 for same reason. or if you use the 064 in the 475.
It is easy to do. If I can do it anyone can.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC
Re: Solo 680 piston
« Reply #6 on: March 20, 2015, 09:12:27 pm »
Yup. A Stihl 064 piston fits with a little work to clear the rod end.
Thanks for info I've got a pretty nice 680 I bought for the coil has scored piston.  Didn't need the coil after all the plug boot had come off the wire just far enough no spark.  Bought it to fix my very low hr. 603.
Shep

Offline Riddler1100

  • 3 cube
  • *
  • Posts: 7
  • Karma: 1
Re: Solo 680 piston
« Reply #7 on: March 21, 2015, 03:07:32 am »
Thanks guys, I'm assuming the piston bosses are fairly easy to just file... Is there a certain "clearance" the pin bosses should be from the crank rod end?? Or does it have to be reasonably tight fit??

Thanks again guys

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: Solo 680 piston
« Reply #8 on: March 21, 2015, 10:50:59 am »
A small gap on each side to accommodate any misalignment of the cylinder as well as allowing fuel/oil mix to the wrist pin bearing would be ideal.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23976
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Solo 680 piston
« Reply #9 on: March 21, 2015, 11:57:28 am »
Anyone got solo 680 piston specs.

There is a guy talking to OP and me saying he used a 272 piston in a 680.


 

Related Topics

  Subject / Started by Replies Last post
20 Replies
4009 Views
Last post March 18, 2022, 07:56:44 am
by Cut4fun .
Solo Rex

Started by Cut4fun . Solo

1 Replies
904 Views
Last post March 07, 2013, 02:30:48 pm
by dutchsawdoctor
Solo 70

Started by Cut4fun . Solo

1 Replies
751 Views
Last post July 03, 2013, 12:57:21 pm
by dutchsawdoctor
2 Replies
411 Views
Last post September 16, 2013, 10:31:32 am
by adam32
Solo 650

Started by brettl Solo

8 Replies
1449 Views
Last post February 20, 2015, 09:01:41 pm
by leec
9 Replies
5534 Views
Last post August 08, 2017, 08:26:32 pm
by Cut4fun .
4 Replies
1024 Views
Last post August 06, 2014, 04:15:37 pm
by adam32
8 Replies
1411 Views
Last post December 09, 2015, 03:17:39 pm
by echo user
5 Replies
1128 Views
Last post February 17, 2018, 12:55:10 pm
by OsageOrange
5 Replies
983 Views
Last post January 10, 2016, 10:50:47 am
by Uncle Lee